Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

R2 MFC Avaya to Cisco 2801 [one way ANI issue]

Hi All,

Today i am doing a POC to test R2 interoperability between Cisco 2801 (VWIC-2MFT-E1-DI + VIC2-2FXS + CP-7940) with Lucent Definity G3 PBX. I used and followed config guide from http://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/cis3600/sw_conf/pbx_int/36lde1r2.pdf

The results are:

1. Voice call from Cisco to Avaya is working, but Cisco's ANI is not shown on Lucent Phone instead it shows Avaya TAC number & trunk name.

2. Voice call from Avaya to Cisco is also working and Avaya's ANI is shown on Cisco IP Phone.

The issue is Avaya's ANI is not shown on Cisco IP Phone.

We asked Avaya's engineer to make a change on Multifrequency-Signaling-Related System Parameters -> request incoming ANI (non-AAR/ASR) to 'y' (Cisco config guide set 'n'). For detailed change see attachment

After tested call from Cisco to AVAYA, call setup took about 10 seconds to connect (before, it only takes less than 3 seconds) however Cisco' ANI is now appear on Lucent Phone.

I used debug to capture the message between them. Here the log.

Apr 22 20:48:16.866: R2 Outgoing Voice(0/0): DSX (E1 0/1/0:28): STATE: R2_OUT_PROCESS_A R2 Got Event R2_TONE_OFF

Apr 22 20:48:16.866: r2_reg_generate_digits(0/1/0:1(29)): Tx digit 'B'

Apr 22 20:48:25.018: htsp_dialing_done(0/1/0:1(29))

Apr 22 20:48:27.398: htsp_digit_ready_up(0/1/0:1(29)): Rx digit='3'

Apr 22 20:48:27.398: R2 Outgoing Voice(0/0): DSX (E1 0/1/0:28): STATE: R2_OUT_PROCESS_A R2 Got Event 3

From message above, on time stamp Apr 22 20:48:16.866, Cisco sends Tx digit 'B' to Avaya, but avaya sends response Rx digit='3' around 10 seconds later.

My questions are:

1. What is Tx digit 'B'? why Cisco sends alphabet as digit instead of numeric? i guess Avaya doesn't understand this. That's why it takes 10 seconds to make respond.

2. Can we modify Tx digit 'B' setting? if not is there ways how to speed up call setup?

Anybody has ever had this issue? Appreciated if somebody could help.

Regards,

Edi

6 REPLIES
New Member

Re: R2 MFC Avaya to Cisco 2801 [one way ANI issue]

Hi All,

I want to make correction. I said on previous email, The issue is Avaya's ANI is not shown on Cisco IP Phone. The correct issue is Cisco' ANI is not shown on Lucent phone.

sorry for this misunderstanding.

Regards,

Edi

Hall of Fame Super Gold

Re: R2 MFC Avaya to Cisco 2801 [one way ANI issue]

Hi, when you configure ANI, it takes a lot of time to be sent. Are you using compelled signaling ? Withi non-compelled it "might" be faster as you don't need to wait for the other party to acknowledge each digit.

New Member

Re: R2 MFC Avaya to Cisco 2801 [one way ANI issue]

Hi,

E1 controller config:

!

controller E1 0/1/0

framing NO-CRC4

ds0-group 1 timeslots 1-15,17-31 type r2-analog r2-compelled ani

cas-custom 1

country argentina use-defaults

metering

!

When I change to non-compelled, calls can't established at all.

Hall of Fame Super Gold

Re: R2 MFC Avaya to Cisco 2801 [one way ANI issue]

The thing is that ANI takes a long time to be sent. You can visualize that with "debug vpm signal" and "term mon" see how many digits are sent, and the total time for that.

Either you remove ANI, make the ANI shorter, or configure the avaya for non-compelled that is faster.

New Member

Re: R2 MFC Avaya to Cisco 2801 [one way ANI issue]

Hi,

Thanks for your suggestions. We will consider to try it.

Anyway, after make change on Incoming MFC Forward Signal I-12 to 'end-of-ani' (which is not wrote in Cisco guide) on Avaya PBX then everything is now going fine. ANI is now appear on both Cisco and Lucent phone.

Many thanks...

Hall of Fame Super Gold

Re: R2 MFC Avaya to Cisco 2801 [one way ANI issue]

Good to know, thanks for the update!

1185
Views
0
Helpful
6
Replies
CreatePlease login to create content