Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

remote config using H323 and SRST

I am going to deploy this config to our remote site and i want to know if you guys think its correctly written. I haven't deployed this in a lab because we dont have extra gateways laying around. Is there a better way of writing this config?

Thanks in advance.

isdn switch-type primary-ni

!

!

voice class codec 1

codec preference 1 g711ulaw

!

controller T1 1/0

framing esf

linecode b8zs

pri-group timeslots 1-15

!

controller T1 3/0

framing sf

linecode ami

!

!

!

!

!

!

interface Serial1/0:23

no ip address

no logging event link-status

isdn switch-type primary-5ess

isdn incoming-voice voice

no cdp enable

!

!

!

voice-port 1/0:23

echo-cancel coverage 32

!

!

mgcp profile default

!

dial-peer cor custom

!

!

!

dial-peer voice 100 voip

preference 1

destination-pattern 1...

progress_ind setup enable 3

voice-class codec 1

session target ipv4:10.128.1.4

dtmf-relay h245-signal h245-alphanumeric

!

dial-peer voice 101 voip

preference 1

destination-pattern 2...

progress_ind setup enable 3

voice-class codec 1

session target ipv:10.128.1.4

dtmf-relay h245-signal h245-alphanumeric

!

dial-peer voice 102 voip

preference 1

destination-pattern 2...

progress_ind setup enable 3

voice-class codec 1

session target ipv4:10.128.1.4

dtmf-relay h245-signal h245-alphanumeric

!

dial-peer voice 103 voip

preference 1

destination-pattern 3...

progress_ind setup enable 3

voice-class codec 1

session target ipv4:10.128.1.4

dtmf-relay h245-signal h245-alphanumeric

!

dial-peer voice 104 voip

preference 1

destination-pattern 4...

progress_ind setup enable 3

voice-class codec 1

session target ipv4:10.128.1.4

dtmf-relay h245-signal h245-alphanumeric

!

dial-peer voice 104 voip

preference 2

destination-pattern 1...

progress_ind setup enable 3

voice-class codec 1

session target ipv4:10.128.1.5

dtmf-relay h245-signal h245-alphanumeric

!

dial-peer voice 105 voip

preference 2

destination-pattern 2...

progress_ind setup enable 3

voice-class codec 1

session target ipv4:10.128.1.5

dtmf-relay h245-signal h245-alphanumeric

!

dial-peer voice 106 voip

preference 2

destination-pattern 3...

progress_ind setup enable 3

voice-class codec 1

session target ipv4:10.128.1.5

dtmf-relay h245-signal h245-alphanumeric

!

dial-peer voice 107 voip

preference 2

destination-pattern 4...

progress_ind setup enable 3

voice-class codec 1

session target ipv4:10.128.1.5

dtmf-relay h245-signal h245-alphanumeric

!

dial-peer voice 10 pots

preference 1

destination-pattern 9.......

progress_ind alert enable 8

direct-inward-dial

port 1/0:23

!

dial-peer voice 11 pots

destination-pattern 9411

progress_ind connect enable 8

port 1/0:23

prefix 411

!

dial-peer voice 12 pots

destination-pattern 9911

progress_ind alert enable 8

direct-inward-dial

port 1/0:23

prefix 911

!

dial-peer voice 20 pots

destination-pattern 91..........

progress_ind alert enable 8

direct-inward-dial

port 1/0:23

prefix 1

!

dial-peer voice 21 pots

destination-pattern 9011T

progress_ind alert enable 8

direct-inward-dial

port 1/0:23

prefix 011

!

gateway

!

!

!

call-manager-fallback

ip source-address port 2000

max-ephones 20

max-dn 100

access-code pri 9........... direct-inward-dial

!

line con 0

line aux 0

line vty 0 4

password 7 104B19101618160E5D

login

!

!

end

2 REPLIES
Silver

Re: remote config using H323 and SRST

It would be really difficult to validate your configuration with out the knowledge of your network topo and dial plans. If you cant try it out in lab, it will always be wise to declare sufficient downtime and have proper rollback plans.

Re: remote config using H323 and SRST

Dial-peers 101 and 102 appear to be the same apart from you've a mistake in 101 ----- session target ipv: should be ipv4: ----- but you only need 1 of them.

you have 2 dial peer 104 going to different destinations.

Other than that it look spretty good, but there's no substitute for having the router point out your mistakes.

Paul

204
Views
0
Helpful
2
Replies
CreatePlease to create content