i have call manger cluster and 2 remote gateway with pri and fxo lines each, both gateways are registered and phones are registered to th ecall managers. i am running h.323. i want that users at each site dial out by using their site pri lines. i have 2 series of DID nos each at each site.what configurations i required at call manager to make this possible
9.1202xxxxxxx - PT_HQ; GW/RL = RL_NY_GW (tollBypass to ny)
9.1310xxxxxxx - PT_HQ; GW/RL = RL_LA_GW (tollBypass to la)
9.[2-9]xxxxxx - PT_NY_LOC; GW/RL = RL_NY_GW
9.1[2-9]xxxxxxxxx - PT_NY_LD; GW/RL = RL_NY_GW
9.911 - PT_NY_9911; GW/RL = RL_NY_GW
911 - PT_NY_911; GW/RL = RL_NY_GW
9.1413xxxxxxx - PT_NY; GW/RL = RL_HQ_GW (tollBypass to hq)
9.1310xxxxxxx - PT_NY; GW/RL = RL_LA_GW (tollBypass to la)
9.[2-9]xxxxxx - PT_LA_LOC; GW/RL = RL_LA_GW
9.1[2-9]xxxxxxxxx - PT_LA_LD; GW/RL = RL_LA_GW
9.911 - PT_LA_9911; GW/RL = RL_LA_GW
911 - PT_LA_911; GW/RL = RL_LA_GW
9.1413xxxxxxx - PT_LA; GW/RL = RL_HQ_GW (tollBypass to hq)
9.1202xxxxxxx - PT_LA; GW/RL = RL_NY_GW (tollBypass to ny)
the above provides all three sites with their own CSS and Partitions as well as defines the gateways for each site.
this is a basic configuration and may not fit your needs exactly as there is much more manipulation of the dialPlan if it's required.
routePatterns are created for each site to offer all sites access to their local gateways for local and longDistance calls. there are also routePatterns for tollBypass.
(an NY (202) user can call an LA (310) number for free via the LA gateway)
NOTE: the use of two 911 partitions, PT_911 & PT_9911 allows for routePatterns to be created that have 'provide outside dial tone' disabled for the 911 pattern, as this would step on the patterns that begin with '9.' that require an outside dial tone if it were not disabled (since there is not preDot digit); resulting in the outside dial tone being played after the first number after the initial 9 is pressed.
i have three sites but gateways are located only 2 sites and at third site there is only call manager. wht i understood is i need to creat route pattern for each gateway separtely and then attach the gateway to that route pattern.
The short answer is that you don't.... That isn't entirely true while at
the same time it kind of is, but for the most part you don't configure
the softkeys. You enable or disable them via TCL. Here is the long
answer. Be sure to read the whole thing or e...
Topology: IP Phone > Switches > Microsoft NPS setup to forward 802.1x
proxy to > ISE 2.1 patch 3 Authentication: EAP-TLS using Cisco MIC SANs
Phone Models 802.1X support? 802.1x flavor Addtl Comment EAP-MD5 EAP-TLS
Cisco 3905 Y Y N Cisco 6911 Y Y N Cisco ...
This document describe how DST changes and how time changes are
implemented in DST. Daylight Saving Time (DST) is the practice of
setting the clocks forward 1 hour from standard time during the summer
months, and back again in the fall, in order to make b...