SRST with Qsig Link

[pdeclercq]

Hello,

I have configured a 2821 with 1 - E1 and 2 - BRI interfaces.

The protocol used for the E1 is Qsig, the is a connection to a siemens Hipath 4000. This connection is working fine in normal mode.

When the Gateway is working in SRST mode I can receive call from the siemens I cannot make calls. In the debuging I see that I try to establish the call but after that the call is interrupted.

Does someone have more information about a Qsig link to a siemens with SRST

Kind regards

[gogasca]

Hi,

Found these links, you may paste your debugs and config so we can take a look.

http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_administration_guide_chapter09186a00803edb19.html#wp1139777

http://www.cisco.com/en/US/products/sw/iosswrel/ps5207/products_administration_guide_chapter09186a0080392682.html#wp1354773

http://www.cisco.com/application/pdf/en/us/guest/products/ps5453/c1072/ccmigration_09186a008035b8ef.pdf

[pdeclercq]

Hello

Thanks for your reply

Here do you have the output for the call under srst

*Nov 16 12:06:19.863: ISDN Se0/1/0:15 Q921: User TX -> INFO sapi=0 tei=0, ns=3 n

r=3

*Nov 16 12:06:19.867: ISDN Se0/1/0:15 Q931: SETUP pd = 8 callref = 0x0002

Bearer Capability i = 0x8090A3

Standard = CCITT

Transer Capability = Speech

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA9839F

Exclusive, Channel 31

Progress Ind i = 0x8183 - Origination address is non-ISDN

Calling Party Number i = 0x0080, '1076'

Plan:Unknown, Type:Unknown

Called Party Number i = 0x80, '027271212'

Plan:Unknown, Type:Unknown

*Nov 16 12:06:19.887: ISDN Se0/1/0:15 Q921: User RX <- RR sapi=0 tei=0 nr=4

*Nov 16 12:06:19.915: ISDN Se0/1/0:15 Q921: User RX <- INFO sapi=0 tei=0, ns=3 n

r=4

*Nov 16 12:06:19.915: ISDN Se0/1/0:15 Q931: CALL_PROC pd = 8 callref = 0x8002

Channel ID i = 0xA1839F

Preferred, Channel 31

Here do you have the output during normal CCM

*Nov 16 12:16:02.191: ISDN Se0/1/0:15 Q921: User TX -> INFO sapi=0 tei=0, ns=0 n

r=0

*Nov 16 12:16:02.191: ISDN Se0/1/0:15 Q931: SETUP pd = 8 callref = 0x0001

Sending Complete

Bearer Capability i = 0x8090A3

Standard = CCITT

Transer Capability = Speech

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA98381

Exclusive, Channel 1

Calling Party Number i = 0x0081, '1076'

Plan:Unknown, Type:Unknown

Called Party Number i = 0x80, '0027271212'

Plan:Unknown, Type:Unknown

*Nov 16 12:16:02.211: ISDN Se0/1/0:15 Q921: User RX <- RR sapi=0 tei=0 nr=1

*Nov 16 12:16:02.243: ISDN Se0/1/0:15 Q921: User RX <- INFO sapi=0 tei=0, ns=0 n

r=1

*Nov 16 12:16:02.243: ISDN Se0/1/0:15 Q931: CALL_PROC pd = 8 callref = 0x8001

Channel ID i = 0xA98381

Exclusive, Channel 1

So during SRST he is using channel 31 ? and I'm getting the message originating address is non-isdn