Cisco Support Community
Showing results for 
Search instead for 
Did you mean: 
Users might experience few discrepancies in Search results. We are working on this on our side. We apologize for the inconvenience it may have caused.
New Member


In SRST mode an incoming call from PSTN E1 pri ---1760--->IP phone user anwers phone the 2 parties chat for a while.Then the IP phone user says hold on bob I'll tranfer you to charlie another Ip phone user.

scenario 1

Charlies phone rings and Charlie anwers they have a chat everything is good.Both parties hangup

scenario 2 Charlie doesnt answer as he is out of the office. So PSTN user hangs up.The issue here is charlies phone keeps ringing.

The call is gone as far as ISDN is concerend normal call clearing.

Why doesnt the skinny tear down the call anyone know of a bug IOS 12.2 15T2 1760 ?

In SRST mode as well ANI is not passed to the phones is this intelligence built in to any version of SRST ?

Ok next I want to went apply a "voice" translation rule 1 1-15rules under call-manager-fallback can this be done in version 3.The reason being is voice translations (not documented anywhere I can find)allow a very complex dial-plan to implemented I have tesed several regular expressions with success that dont work with a translation rule though I cant apply this in CCM fallback like a normal translation rule : (

Next question which the TAC couldnt tell me

I want to create CoR for a couple of phones whe SRST mode.

The problem ithe way I see it is that phones register dynamically in srst and a directory number gets assigned a dial-peer first come first served.20001 20096 if i allowed 96 dn max this would be the case.

So how do I apply a Class of restriction ?

The documentation on COR 12.2 2t is absoloute garbage and makes little sense to me .

I'm hoping it can be defined by directory number for example dn 4000

So if someone could give me a working example, one of you Cisco guys must know or have done it or can test it in your lab I would very much appreciate it .

New Member


This is a config from CCO under call-manager fall back these are applied cor incoming allowall default

cor incoming allowall 1 4000 - 4999 This is saying ext numbers can call 911 1800 1900 but no other numbers is this correct ?

cor incoming allowall 2 4000 - 5000 whats the poit of this ?

dial-peer cor custom

name call911

name call1800

name call1900



dial-peer cor list allowall

member call911

member call1800

member call1900




dial-peer cor list allow1800

member call1800



dial-peer cor list alloww1800and1900

member call1800

member call1900


dial-peer cor list allow1900

member call1900


dial-peer voice 1 voip

destination-pattern 919715....

translate-outgoing called 2

session target ipv4:


dial-peer voice 2 voip


destination-pattern 6....T

session target ipv4:

codec g711ulaw


dial-peer voice 3 voip

destination-pattern 65087.....

session target ipv4:

codec g711ulaw


dial-peer voice 90 voip

corlist outgoing allow1900

destination-pattern 9000

session target ipv4:


dial-peer voice 45 pots

destination-pattern 9

port 1/1/0



ip source-address port 2000

max-ephones 10

max-dn 10

dialplan-pattern 1 408735.... extension-length 4 no-reg

dialplan-pattern 2 919785.... extension-length 4 no-reg

voicemail 4001

no huntstop

alias 2 3... to 5555

translate called 1

call-forward busy 5001

call-forward noan 5001 timeout 8

cor incoming allowall default

cor incoming allowall 1 4000 - 4999

cor incoming allowall 2 4000 - 5000


time-format 12

date-format mm-dd-yy

transfer-pattern 1...

transfer-pattern 2...

keepalive 30

interdigit timeout 5


line con 0

line aux 0

line vty 0 4


line vty 5 15


CreatePlease to create content