Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

Unable to install the GB 1.1.5 DialPlan

Whilst attempting to install the GB 1.1.5 DialPlan in order for new O2 mobiles numbers 075, the installation failed due to the reason that the tags BROADBAND-SERVICE have clause configured but are deleted in the new dial plan version.

Any suggestions would be apprepriated?

11 REPLIES
New Member

Re: Unable to install the GB 1.1.5 DialPlan

I also need to update one of our customer's dialplans due to the new O2 mobile prefix.

Alan, do you know if it's possible to manually update the existing dialplan file with the following?

# 0+7[5-9]XX+XXXXXX

P: 0 NATIONAL-ACCESS

P: 7[5-9]XX MOBILE-ACCESS

P: XXXXXX MOBILE-SUBSCRIBER

If so are there any caveats that I need to be aware of?

New Member

Re: Unable to install the GB 1.1.5 DialPlan

I need to install this dial plan also - where did you find it??

Running CM 4.1

Re: Unable to install the GB 1.1.5 DialPlan

The dialplans should be located under the locale installer on the Voice software downloads page.

Click on Version 1.0 under DialPlan and the GB one should be second from the top.

Click the following link.. You need to logged-in CCO.

http://www.cisco.com/cgi-bin/tablebuild.pl/IDP

New Member

Re: Unable to install the GB 1.1.5 DialPlan

I have followed that link but it just tells me that there are "currently no files of this type"??

Re: Unable to install the GB 1.1.5 DialPlan

Try this one, then select version 1.0 from under the dial-plan at the bottom of the page.

http://www.cisco.com/kobayashi/sw-center/telephony/callmgr/locale-installer.shtml

Regards

Allan.

Re: Unable to install the GB 1.1.5 DialPlan

You can update the plan manually, however it takes effect every time you cycle the CallManager service.

What you also need to be aware of is that that DNA also needs restarting for DNA to reflect the change.

Regards

Allan.

HTH..

New Member

Re: Unable to install the GB 1.1.5 DialPlan

that's perfect, thanks!

Re: Unable to install the GB 1.1.5 DialPlan

Has anybody come across this problem before concerning the upgrading the DialPlan and disassociating TAGs from Route-Filter clauses?

I have removed the Broadband-Service TAG from route-filter in question, and yet when you attempt the install again it still complains about the same TAG and it does not exist in any other route-filter?

The route-filter was restarted and reset, the CallManager service was restarted but all of this was to no avail.

Incidentally this on CCM5.0.4.

Thanks

Allan.

New Member

Re: Unable to install the GB 1.1.5 DialPlan

Hi Allan,

The way i got round it was to remove the route filters from the route patterns delete the route filters and uninstall 1.1.4 on all servers. Restart ccm service install 1.1.5 on all servers.Restart ccm service configure route filters add to route patterns. The Broadband-Service tag does not exist in the new dial plan. I have raised a tac case with cisco and still awaiting a reply.

Silver

Re: Unable to install the GB 1.1.5 DialPlan

Has anyone got any updates on this- is the method posted earlier re filters etc the only way to install the new version?- thanks

Re: Unable to install the GB 1.1.5 DialPlan

Unfortunately simply removing the route filter from the route pattern and then just deleting only the route filter in question with the broadband service tag does not work by itself.

Unless Dave has had any feedback from Cisco regarding his TAC case then the workaround is as he mentioned, remove all filters and uninstall the dialplan prior to installing 1.1.5.

Unfortunately I have not had the opportunity to carry out the workaround provided by Dave, as there doesn't seem to be any pressure from the customer due to OOH requirement when removing the filters.

Regards

Allan.

420
Views
10
Helpful
11
Replies