Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Video Conferencing QoS Type?

I have a T-1 link between a 3660 running 12.0(7)XK1 and a 2611 running 12.0(3)T3. All my internet and data traffic run across this T-1 between sites and also my video conferencing. We are using Polycom H.323 units. I've read several of the QoS documents, but am still confused on which way is the best to go. There are issues with the video conferencing when a large file is being transmitted. Any specific ideas to help with this?

11 REPLIES
New Member

Re: Video Conferencing QoS Type?

New Member

Re: Video Conferencing QoS Type?

Try implementing the Cisco MCM, it will prioritize H.323 traffic onthe links.

If you do not have a pure Cisco network look at CSU from ADC that support Service point, they can filter and prioritize packets on the WAN links.

New Member

Re: Video Conferencing QoS Type?

Have you looked at LLQ Low latency Queuing. I have a similar configuration using the PolyCom units in 8 locations and have had very good luck.

New Member

Re: Video Conferencing QoS Type?

How do u implement the QOS?

U are running on what type of network? Is it IP/ISDN/ATM/Frame relay?

What model of router u used?

What is the bandwidth of your WAN link..?

Can u e-mail to me the example of configuration..?

New Member

Re: Video Conferencing QoS Type?

Why don't you post the configuration of your wan I.E. topology, whether or not it's atm or atm-frame CIR's pt to pt etc. These things all factor in when someone is recommending help to you. No one can give you a good answer until that stuff is cleared up first.

At that point, I am sure you can get better answers to your question.

Regards,

Chris

New Member

Re: Video Conferencing QoS Type?

If my network base on frame relay,one center and 17 branchoffice,how i apply QoS? LLQ can apply on frame relay ,or cannot?

thanks

Cisco Employee

Re: Video Conferencing QoS Type?

You should classify your video traffic as IP Prec. 4 and service the traffic out of a LLQ. Provision the queue with the data rate of the call plus 18%. You can reference the Cisco QoS quide at http://www.cisco.com/univercd/cc/td/doc/product/voice/ip_tele/avvidqos/index.htm

Alan

New Member

Re: Video Conferencing QoS Type?

I understand that LLQ works in conjunction with FRTS. I also understand that FRTS, once applied, will set every subinterface into a default class unless otherwise specified. In our design, the FRTS would have to be applied to a physical interface with about 100+ other subinterfaces. We don't want to risk effecting the throughput on those other interfaces.

Is there another way to apply QoS on frame relay so as not to interrupt other subinterfaces?

Thanks.

New Member

Re: Video Conferencing QoS Type?

One option to consider is the application specific routing (ASR) feature available in the Cisco MCM/QoS Proxy. It can segregate H.323 traffic and send it to a specific wan port.

Cisco Employee

Re: Video Conferencing QoS Type?

With the versions of code you mentioned above LLQ is not an option, 12.1X is required for LLQ. You need to implement queuing of some type to address your issue. If you could go to 12.1 I would suggest using LLQ and using a priority statement to insert your video calls into a PQ. You could try CBWFQ and see if that helps.

New Member

Re: Video Conferencing QoS Type?

I was use 120-7.T for apply llq in FR. but my problem is that service-policy comand it is not apply to map-class for a VC. only It is apply to serial interface. It is very important for llq work or only of this form the llq is apply to all VC of the serial interface

946
Views
0
Helpful
11
Replies