I am receiving an error message during debug on our serial point to point line. The message is: "Illegal HDLC serial type code 777, PC=080017240". The reason for the debug is that the interface is up/down and will not go up/up. I have had the lin...
I am receiving an error message during debug on our serial point to point line. The message is: "Illegal HDLC serial type code 777, PC=080017240". The reason for the debug is that the interface is up/down and will not go up/up. I have had the lin...
PASSWORD RECOVERY IS DISABLEDGot this message on 3630.Tried to use Cntl-Break.It help me get to the question:Do you want to reset the router to factory defaultconfiguration and proceed [y/n] ? Then I enter "y" and got next message:Reset router config...
I have two separate routers w/2 separate multicast lan sources streaming data....I run into trouble when I bring up a new redundant link that adds a second route to the same multicast source router...being that the second route has the higher IP addr...
I've ordered some long distance 2.5 Gig circuits (OC48) which I was going to run using POS as it's nice and simple for IP. I was going to terminate them on 7609's and push them out to the LANs on GIGE.However I've now been asked to carry an older IG...
Beacause:1. 3550-T 10/100/1000 port to T-GBIC WS-G5482 in 3550-48. These cables work(full duplex, speed 1Gb ): a. 4 pair Cross-over(1,2<->3,6) (4,5<->7,8) b. "Classic 10/100" 2 pair Cross-over(1,2<->3,6) (4,5,7,8 straight) c. Straight (1,2,3,4,5,6,7,...
Hi All,Did anyone out there have successfully browse snmp on the local director?Steve
hello,i have a fa4/3 port and i want to use it as a router interface instead of a switchport.this is because i have to do a rate-limit both directions on that port.now - i don't know why .... but it doesn't work ... the rate-limit ...here is what we ...
I have multipul 6509's at my access layer. I am currently experiancing ports going error disabled due to late collisions. My connections to my devices are 100/full. My concern is that I have just had a 100/Half connected device go error disable with ...
Hi everybody,I have a problem.There is a WAN over ISDN with CISCO 760 routers.LANsuse private IP addressing and are connected together through DDR viaprofiles.Now the customer wants connectivity from each site to the ISP.The solution would be the PAT...
Want to know if there are any limitations to using CEF.I have two T1 and want to bond them is there any issues with reordering of packets.
I have a 4700 that attaches to an LS1010 via a fiber connection. The connection suddenly ceased to pass data. I have changed out the fiber patch cords, tested the fiber backbone, both warm and cold booted both devices, etc.etc...... The interface ...
I have two Cat4006 boxes, one with a WS4232L3 Router module and about ten 2924C switches, each in their own Vlan, all trunked together using 801.q. Im trying to backup my configurations to a tftp server. I can do it with no problems from the 2900...
Hello;Can you implement DDR on a serial interface using a Multitech modem to backup a ADSL link?Thanks
Just replaced the 2501 router with 1 2621 router for a customer. They are running a frame-relay circuit 256k. All we did is configure the same exact configuration on the 2501 to the 2621. After it went online, the connection was extremeley slow. ...
I need to transfer multicast packets (three of four ip multicast addresses) from one LAN to another LAN. What is the most simple configuration to achieve that?I have one or two routers between both LAN's.TIA
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
02-20-2024 07:45 AM | ||
02-15-2024 09:08 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM |
User | Count |
---|---|
2 | |
1 | |
1 | |
1 | |
1 |