question is can i apply same ip address to different unnumbered serial interface, eg apply in unnumbered ethernet0/0 to both serial0/0 and serial1/0?
question is can i apply same ip address to different unnumbered serial interface, eg apply in unnumbered ethernet0/0 to both serial0/0 and serial1/0?
I have installed SurfControl on a new server on my network to monitor Internet traffic through a Cisco 1720 router. All users are connected to a single 2950 Switch.SurfControl needs to utilize mirror/span info from the Internet Gateway (19) port to t...
I am having major problems configuring my AUX ports (I know, they are not truly a "port!") to accept inbound calls for remote access to the router for management. I have several 3600-series, 2600-series and a couple of 2500-series routers that work ...
Hi All, Does anyone know if Cisco 3640 router's backplate can support two DS3 connections?
Does anybody know what this error means?00:30:27: %GT96K_FEWAN-5-UNDERFLOW: Transmit underflow on int FastEthernet0/000:30:27: %GT96K_FEWAN-5-UNDERFLOW: Transmit underflow on int FastEthernet0/000:47:09: %GT96K_FEWAN-5-UNDERFLOW: Transmit underflow o...
Hi all,i am having cisco 2520 router and has 64 kbps link to internet which is using thru NAT. We have got 6 no public ip from our ISP and we r using only 1 for NAt , so if i want to use any of public IP to my PC in LAN how should i configure ....pls...
We have inherited the CW2K and I am trying to figure out the LMS version we are currently at. The CW2K we have is LAN Management with Essentials version 2.0 and Campus version 2.2. Can anybody please tell me which version of LMS this would correspond...
We are having problems with users putting SOHO routers on 3524 switch ports (backwards) and suddenly becoming a DHCP server for the users on that switch. Is there anyway to filter these responses? Are there any other suggestions for a solution?
We're looking to upgrade our CW2000 to the latest version and are being charged $15000 for an upgrade. Is this about the right ballpark number? Can someone please confirm? Thanks.
I am redesigning our WAN with 4 offices and I have decided on Leased Lines. Can anyone give me some good advice from the field on Design Tips or a resource that will give good design tips. I've read the Cisco papers, but I feel as If there should be...
I have connected an external dsl-modem to a cisco 1721 router.Normally, cisco routers use the interfaces keepalives to detect wheather the line protocol is up or down. On normal ppp links the LCP CONFIGURE REQUESTS are used as keepalives.Now we are t...
We have a new installed E3 circuit.By doing "sh cont e3 0/0" i get a lot of data, alos the above mentioned message.Is that anything to worry about?Regards Karl-Heinz
Can anyone please tell me if the power supplies for data on this switch require a 20-amp type receptacle, the one with one of the straight connectors horizontal and the other verticle?
Can you run clear commands in Netconfig or is this strictly to run configuration commands and or show commands . I have been trying to do a clear counters on switches or routers and it doesn't seem to work .
This is a long one and I appologize if it seems rather simple but I need some help. We have a single 2620 router and 2 PIX firewalls, one with 2 interfaces (Pix02) and one with 3 interfaces (Pix01), behind it. The networks are all subnetted from a ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
02-20-2024 07:45 AM | ||
02-15-2024 09:08 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM |