Other Network Architecture Subjects

Hi everyone ! I have this problem: in a Central Site I configured a Cisco 2610 router connected with a 2 ISDN device (s/t). In a 3 remote site I have connected 3 (one for each site) cisco 801 router. My problem is that when a Cissco 801 call a Centra...

I'm curious to know if it is possible to collect bi-directional netflow records over two separate VLANs. I have a single-mode fiber line run between a Catalyst 6509 and an F5 Networks BIG-IP box. I have two VLANs set up on that link, one for inboun...

This may be beyond the scope of this board, but has anybody used the Net::Telnet::Cisco module for Linux to automate backing up a down line? Until Cisco implements a fail over for ethernet interfaces that go down without physically going down, I'm s...

Hello ,We have Cisco 3640 RAS server (IOS 12.0) on our Network for Dial in connections from home users . It has got own user database (no RADIUS & TACACS ) and we do create user accounts on 3640 itself . It has one FE port which connects to local...

Does anybody out there know if I can get a Shiva ISDN Accessport/D ISDN router to work with a Cisco 2500 Bri interface using dialer map etc. I can get the two to make calls to eachother and authnticate but thats all.

Greetings everyone,We are trying to monitor traffic at one of our sties on a 2950 and have run into a problem where the dst port goes line protocol down. There is only one switch and int fa0/24 connects to our 3640 router. Int fa0/23 is where the s...

i have a switch (5500) at a remote location with an ip address of a secondary interface. i need to change the switch to it's new ip address. if i were to do this remotely, what would happen? i should just loose my telnet session, correct? just want t...

Hi guys,I have a question, what is the diference between trunk and EtherChannel, I have 2 Switches 2924XL connected using the 2 fiber link on ports 23 and 24, How can I make a load balance between this 2 ports ?Thanks,Alex

helloi heard that we can configure a new cisco router via its AUXILARY port. does any one try it? some other say that the config via AUX port is only available via remote access (PSTN) to AUX port!! is it true?

I need to connect corp LAN to multiple WANS connected to Internet to increase Corp Lan apparent bandwidth.Example:4 10MB ethernet WANS from same ISP to 1 100 MB corp LAN.Can I do this with a Cisco router such as 7600???Thanks, Scott

Hi All, Can anyone give me a hand with the port forwarding capabilities of a PIX 501?? What I'm trying to do is forward port 3389 (windows terminal services) to a W2k server. I tried using access list settings in the GUI for this to no avail an...

Hi,Let's say I have a public address of 150.10.10.1/16 on a isdn link for my internet connection, and i have a server on 192.168.111.1 on the e0 interface. Everything is configured and I can go on the internet from the server. Now I want users from t...

I'd like to know how to configure a cisco 1003 IOS 11.3.11 to accept async dial-in connections from modemsThanksStefano Colombo

Hi,I am trying to install RTM 1.3 on Win2K SP2. During the inst an error message occurs "cannot create secured user". Nonetheless, a user ngenius is created. But the nGenius service cannot start due to a "logon failure" according to Windows event vi...

As far as I know I have CiscoWorks2000 for Solaris 2nd Edition. This may seem like a stupid question but I need to confirm this. Is this version purely for Solaris? The documentation gives details about an NT install and this is the reason I'm asking...