Does the Cat2950 switch support VLAN numbering above 1024 ?Or will it support this in the near future ?I need this for connecting non-Cisco switches with 802.1q support and VLAN numbering 1-4096 to Cat2950.rolf
Does the Cat2950 switch support VLAN numbering above 1024 ?Or will it support this in the near future ?I need this for connecting non-Cisco switches with 802.1q support and VLAN numbering 1-4096 to Cat2950.rolf
Has anyone seen this or have any ideas?Using Campus Manager>managed networks>layer2 viewI can view my picture of my LAN/WAN and all objects however I get some LAN zones which are displayed as red or green horizontal bars. I have checked and compared...
Why Check Device Attributes shows an incorrect rw snmp community for my 7507 and 7204VXR with this configuration?access-list 1 permit 10.41.52.100access-list 2 permit 10.6.61.40access-list 2 permit 10.6.61.43access-list 2 permit 10.6.61.76snmp-server...
If i configure the inter vlan multicast routing in the 2 L3, the multicast trafic is duplicated in the client vlan.How can i configure the redondant multicast routing ?ip multicast-routing enable at the general levelip PIM dense mode enable in all th...
I have 2 x RSMs on 6509s running HSRP servicing a VLAN on which I'm trying to install two servers acting as cluster ie. same IP address and same MAC 03-xx-xx-xx-xx-xx.access from the LAN is OK , but I'm struggling with WAN access. The routers do not ...
I recently inherited a 7010 with RP/SP running version 10.X. I need to upgrade it as far as possible (11.X) and have a 16MB Flash card for the RP. It's an Intel 2+. Anyway, All the documentation I can find here on the Cisco site says I should "Fo...
Hello Can anyone please tell me if the 7206 slot modules are hot swapable? Thanks
DFM 1.1 does not see the 3rd power supply in my 4006 switches.Any ideas on how to get DFM to see them. When the 3rd PS goes down. DFM never sees a trap nor does my NMS.
I'm having problems with Dial-in connections. Everything is ok but the disconnect after about 1-7 minutes. According to the syslogs & traps the case is Lost Carrier. Sudden retains are initiated. I've checked the Earthing, the peak voltage to nol is ...
Hello Everyone,I have three routers that are connected via a 768k frame relay network. Each router has two frame relay permanent virtual circuits (PVC). I configured traffic shaping to optimize my congestion and control the flow of traffic. I w...
I need this info but i can´t found it in CCO.Thanks
how long should it take to backup 1.5gig's over my wan connection.... here is my topology.A. client computer set to 100 FULL (not auto) connecting to a 3524B. 3524 is connecting to a 2507 via ethernetC. 2507 is connecting to a 3640 via a frame circui...
When pinging from a telnet session on my 2620's serial interface, I cannot get responses back from a host on the ethernet LAN until I set the 2620's ethernet interface as the gateway on the host. So my question/assumption is this - will the packet th...
What, if anything, needs to be done to any of the components of CiscoWorks2000 for a server backup? I.e. With HPOV, one needs to pause the databases. Is there any backup strategy for CiscoWorks2000?
Any suggestions as to how I can isolate this problem? I have two Cat5509s both with RSMs, only using one of them. The switches are linked via 2 gigabit connections on the Supervisor card. Thanks,Doug
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
02-20-2024 07:45 AM | ||
02-15-2024 09:08 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM |