Hi,I am facing competability problem between CISCO 12010 router's POS port with SDH STM1 PORT.So we need to change s1s0 values on router POS port.So please suggest with posibile command to configure s1s0 values on router POS port.
Hi,I am facing competability problem between CISCO 12010 router's POS port with SDH STM1 PORT.So we need to change s1s0 values on router POS port.So please suggest with posibile command to configure s1s0 values on router POS port.
I know how to subnet a Class C adress. However, there is a question of a class B adress that I can't figure it out.This is what I know, this is a simalar question.What is the broadcas adress of this IP172.16.10.33? /27 ?Answer is:/27= is 3 bits so i...
Hello,I've got a stack of 3750 switches connecting to a PIX 515e then off to an ISPs router...We have a 20meg link from the ISPs router to the Internet.But, we are not getting 20 meg speeds when we download anything from the Net. I've done countless ...
Good afternoon everyone,I've been working on creating some new qos policies that we apply to ATM PVCs that are built up on ATM SPAs in a SIP-200 on the 7600 series routing platform. I'm running into a bit of a brick wall when looking at what some of...
Dear allI'm having a very strange situation here (at least for me)we have 4 core switches2 x WS-C3750G-24T-S Catalyst 3750 24 10/100/1000T + IPB Imageand2 x WS-C3750G-12S-S Catalyst 3750 12 SFP + IPB ImageStack configuration is done this waywhen ...
HI, I want to known if there is a command like calling-number outbound for E1's with R2-Digital ?I use the reverse telnet at 7001 port to dial to a provider and I need that on the providerappears 30 different numbers instead only one (E1's trunk one...
Hi,Can you do DMZ and NAT/PAT with a single public IP address on ASA5520? I have uplink in PPPoE and has only one public ip address. Would like to put anti-spam(eg. A.B.C.44) in the DMZ and there are a number of servers(eg. X.Y.Z.1, X.Y.Z.2 and X.Y.Z...
Hello Community!I have the following question. I have routers running X25 encapsulation on their serial interfaces and I have also enabled the following commands on the respectve interfaces: ip nbar protocol-discovery ip flow ingress ip flow egress i...
I am having problem with one of my SPA-2X1GE cards in cisco 7606 router.There are two SPA-2X1GE in my router and one is not coming up.Previously it was having the IOS Image:c7600rsp72043-advipservices-mz.122-33.SRD3.binbut now we upgraded a new IOS s...
I have been looking round the Cisco web site to no avail. Is there any limit on the number of access list entries on either a 2811 or 7206?Thanks,Paul.
HelloI need to boot Cisco1841 with USB Drive instead of Compact Flash but I don't know what should I do.I heard I need to format USB Drive with FAT and need to save IOS on the USB Drive.Before boot, Need to set config register ? I am not sure which p...
I've been tasked with configuring a number of 3560's. I thought it would be good experience to learn to do an Xmodem transfer, so on one switch I erased the flash. This wasn't too big of a deal, as I already had everything I needed. After erasing ...
my cisco asa 5505 will not boot. it goes into ROMMON. i need help getting it back up again
Does anybody know what the transmitter minimum power and receiver minimum sensitivity of Cisco 10G cards such as X2-10GB-LX4 or X2-10GB-LR are?
Hi AllI'm running a couple of stacks of 3750's and I am having a problem with the Software syncronisation feature. Basically, the sync does not work. When I add an additional switch, the systems detects the out-of-date sw-version and tries to replic...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
02-20-2024 07:45 AM | ||
02-15-2024 09:08 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM |