I'm going to take a crack at CCIE Routing and Switching certification. Any suggestions for training materials.
I'm going to take a crack at CCIE Routing and Switching certification. Any suggestions for training materials.
Dear Cisco TeamCould you please clarify if the following port adapter in 7200 / 7500 can support E1 G.703 ( Unframed ) Configuration like PA-4E1G/120 without configuring ATM parametersPA-A3-8E1IMA Eight-port E1 ATM port adapter with IMA Thanking...
I have this configuration on my ASA :- outside (WAN) : 10.0.0.254- inside (LAN) : 192.168.100.254- dmz : 192.168.110.254In my DMZ, I have a https server which can be accesible from internet. So I have created a nat rule to redirect the port 443 :#> s...
Hi,We have 7609S with redundant sup 720-3B working fine with active and standby hot position.Now I want to club both the sup's gigaethernet interface with same ip address.Can I do this? if yes than how please suggess me
My router 3745 boot on ROMMON mode could you help ?Many thinks
HiCan i perform policy based routing with 4503 switch having SUP II + TS or i need to have router to perform this PBR? kindly provide links to the documentation if possible.regards
Hi, i have an issue with a UPS software to automatically shut down clients in the event of UPS battery draining completely after a power cut....we have 3 different subnet on our PIX and the software uses broadcast method to discover clients and list...
I have 6 Dell ServersI want to run 2 www servers, 1 master DB and one back up server, an image server and DNS serverswe get a traffic between 10,000 to 100,000 depends what time of the day.I am thinking of getting a Cisco 4948 and ASA firewall.For a ...
Dear AllPlease I need Help:I have the connection like:Router1--> Router2 with switchport Card --> PC.The configuration for PC:IP Address 10.244.29.234SubnetMask: 255.255.255.252The Router2 with Switchport Card:interface FastEthernet0/3/1 switchport a...
Hi,By reposting, I'm hoping to get some replies. If it's not possible, please let me know.http://forums.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Network%20Infrastructure&topic=LAN%2C%20Switching%20and%20Routing&CommCmd=MB%3Fcmd%3Ddisplay_l...
Hi!I have a config:---ip nat inside source list 10 interface Dialer0 overload!access-list 10 permit 192.168.202.0 0.0.0.255access-list 10 permit 192.168.205.0 0.0.0.255access-list 10 permit 192.168.214.0 0.0.0.255access-list 10 permit any log---My PC...
While troubleshooting a problem with a device, I was pinging using a data size of 1600 (ping -l 1600), which just timed out. But pinging other devices on same subnet, ping -l 1600 works fine. This leads me to believe ICMP packets are not blocked an...
HiI have redundant pagp channels to core from access, no distribution layer...so I want to migrate to lacp. Can I just configure one of the pagp that is in blocking mode to lacp without any weird stuff happening?dont have a test environment to see so...
Hi all, I am experiencing an RSTP problem. I have two swtitches connected via wireless link, the port is in trunk mode, the native vlan is vlan 1 the problem is that bpdu's are exchanged for other vlan's but not for vlan 1, when i connect a sec...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
02-20-2024 07:45 AM | ||
02-15-2024 09:08 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM |