is it possible for me to find out the actual speed of the link connected to my serial interface on the switch ? does it auto detect it ?
is it possible for me to find out the actual speed of the link connected to my serial interface on the switch ? does it auto detect it ?
hallois there a way to know if a cisco catalyst switch is working in store-and-forward, fragmentfree or cut-through ?Can we change with ios the switching mode ?regardsfrancesco
Hii need to know with detail what does it mean this command"passive interface vlan 50"?;description;usefulllink it is very much appreciated.10xsali
I read many articles in Cisco webpage that i can make etherchnnel between normal ports in two switches catalyst.Can I make an Etherchannel using two uplink ports on a Catalyst 2950T and two normal ports on a Catalyst 2960G?. Thanks
Hi Expert,How can I limited the route from advertised to a neigbhor?The network setup is as follow:Subnet A - Router A -- Router B - Subnet BSubnet CRouter A have subnet A and CRouter B have subnet B.I want to stop router A advertised subnet C to ...
I have a router with two interfaces which of course have two different subnet ranges. This is going to be on a network with two possible paths to the Internet. I need to have traffic go in two possible directions. I also need to have a NAT pool so...
I am experiencing the following problem at a client site any suggestion on how to resolve this problem would be greatly appreciated.The client has got 2 Cat6509 core switches, there is a cat4507R with a Sup4 hanging off these two core switche...
If I have 2 dialler interfaces, and 1 BRI interface, can i just put them both in dialler pool 1, or do I need to have 2 different pools for the dialler interfaces, and then put the bri as members of both ?
I am to try to redirect port 3500 of dialer0 for an IP 192.168.1.2 in the Lan whit the same port number. Already I moved in nat. E I created rules ACL. But I did not obtain.Router cisco 836 My config:!no service padservice timestamps debug datetim...
i have got 1 3750 L3, having vlans mentioned below.2 Routers 1700 series(main center) connected to the 3750, 2 other routers connected on the remote location which is connected in the main center routers.few machines are in vlan 3.Main Center Routers...
Does anyone know how to clear out the configuration buffers on a 800 series router (other than a reload)?error:router#wr memBuilding configuration...% Configuration buffer full, can't add command: 10.10.10.10%Aborting Save. Compress the config, Save ...
Sir,If I have no BRI port and I want to connect internet through ISDN line then what we will do ?
Can I use the reserved VLANs as normal data VLANs ?Reserverd VLANs: 1002-1005Thanks,Cleber
HI ALLWe have a network with core;dist;access.EIGRP IS The routing protocol;each dist has connectivity(ETHER) to the CORE each location has an explecit route to the every poosible subnet.i dont want to see the route from vlan 50,60 in routing table o...
i am confused the different between switching capacity and forwarding rate ( performance of CE500 show at this link http://www.cisco.com/en/US/products/ps6545/products_data_sheet0900aecd80322aeb.html ), and In some data sheet such as router 1841, the...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
02-20-2024 07:45 AM | ||
02-15-2024 09:08 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM |