Other Network Architecture Subjects

Ok, got my Eigrp static route redistributed. But now Eigrp on site 2 complaining that every vlan is not "common" on both sites. Vlan192 links Site1 to Site2Site1 EigrpConfig:router eigrp 700 redistribute static metric 10000 1000 255 1 1500 network 10...

I have a router with two physical gi port.I create two subinterface on each gi port.internet = gi0/0.1remote site = gi0/0.2firewall = gi0/1.1local lan = gi0/1.2How can I create routing between the firewall and internet subinterface, and routing betwe...

Hi,I am trying to connect a 2950 switch with EI to the network through a third party switch. I need to make the 2950 switch an ordinary switch with no STP/VTP/CDP running on it. I have already diabled CDP and I have not configured anything for VTP....

Hi, we have implemented NLB on the SGI Server running IRIX OS, it works fine. the connectivity is 2 NIC connected on 3750-1(ruuning HSRP),now if i connect 1 of NIC in to the other switch 3750-2(running HSRP) will the NLB workz & will i get the 2Gbps...

Hi,on interfaces configured as trunk, likeinterface GigabitEthernet 1/0/1 switchport trunk encapsulation dot1q switchport trunk native vlan 11 switchport mode trunk!and 'errdisable' detect and recovery configured for all causes with a timeout of 300 ...

Hi,I need to bridge the both building with the same IP subnet but different VLAN id. (within a cloud).Can that be achieved??Building A - VLAN 1 (10.10.10.0/24)Building B - VLAN 5 (10.10.10.0/24)Thanks.

HelloI need to setup vlan routing on a 3845 running 12.4 IOS. I have 4 VlansVlan 2Vlan20Vlan50Vlan100I need to be able to route between all vlans from 2 to 20 to 50 to 100 and 100 to 50 to 20 to 2. How do I do this. Does anyone have a config to ac...

I'm planning to upgrade the ios on a 6500 switch with a sup720/pfc3/msfc3. how do i determine the amount of RAM on the supervisor? The show version command displays "cisco WS-C6509 (R7000) processor (revision 3.0) with 458752K/65536K bytes of memory....

Please see txt file with all the info.Summary- Want use EIGRP as my primary routing protocol between two sites. If connecting Layer 2 circuit betweens sites fails, floating static routes will take over and direct traffic to a vpn device. Problems:1.C...

I would like to know if there are any guidelines as to preference for loading system images. i.e. sup-bootflash: bootflash: disk0:. What is the difference between the sup-bootflash and bootflash.

Is it possible on a 1811 to change the 8 switchports to routed ports?

When I try to format a flash card inserted in to sup-slot0: on a native IOS (Cisco 6509) I get the following error:Hammond_Core_6509_1#format sup-slot0:Format operation may take a while. Continue? [confirm]Format operation will destroy all data in "s...

Hi,we recently bought a 3650g from our supplier. On receiving it we noticed the power supply socket was sitting inside the chasis and seemed a little loose. The other cats 3500/50 we have, have the power firmley gripping the chasis. We sent the switc...

To make a long story short, we have a 6500 L3 switch as our core switch for our corporate LAN. There is a 3550 connected to it by fiber, and a 3750 is connected to the other side of it also by fiber. I can go to the 3550 in the middle and ping/teln...