Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

00:10:33: %ATMCORE-3-INTERNAL_ERROR: CTT row 3800 is internally created.

Hello,

Do you know what is this about?

CTT row 3800 ... it seems the box doesn't accept any commands I try to provision under the dsl ports.

Here is what I have:

dslam02-test.40nr# sh ver

Cisco Internetwork Operating System Software

IOS (tm) NI2 Software (NI2-DSL-M), Version 12.2(12)DA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

TAC Support: http://www.cisco.com/tac

Copyright (c) 1986-2003 by cisco Systems, Inc.

Compiled Wed 23-Apr-03 11:55 by torowe

Image text-base: 0x800082EC, data-base: 0x8173C000

ROM: System Bootstrap, Version 12.0(5)DA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

BOOTLDR: NI2 Software (NI2-DBOOT-M), Version 12.2(12)DA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

dslam02-test.40nr uptime is 12 minutes

System returned to ROM by power-on

System image file is "flash:ni2-dsl-mz.122-12.DA2.bin"

cisco 6160 (NI2) processor with 60416K/5120K bytes of memory.

RC64475 CPU at 100Mhz, Implementation 48, Rev 0.0

Bridging software.

1 Ethernet/IEEE 802.3 interface(s)

16 G.SHDSL DSL Port interface(s)

4 ATM network interface(s)

522232 bytes of non-volatile configuration memory.

4096K bytes of Boot Flash (Sector size 128K).

16384K bytes of Flash internal SIMM (Sector size 256K).

Configuration register is 0x2102

dslam02-test.40nr#sh hard

dslam02-test.40nr#sh hardware

Chassis Type: C6160

I/O Card: 6160-DS3-IO

Slot 1 : STUC-8-TCPAM Slot 18: EMPTY

Slot 2 : EMPTY Slot 19: EMPTY

Slot 3 : EMPTY Slot 20: EMPTY

Slot 4 : EMPTY Slot 21: EMPTY

Slot 5 : EMPTY Slot 22: EMPTY

Slot 6 : EMPTY Slot 23: EMPTY

Slot 7 : EMPTY Slot 24: EMPTY

Slot 8 : EMPTY Slot 25: EMPTY

Slot 9 : STUC-8-TCPAM Slot 26: EMPTY

Slot 10: NI-2-DS3-DS3 Slot 27: EMPTY

Slot 11: EMPTY Slot 28: EMPTY

Slot 12: EMPTY Slot 29: EMPTY

Slot 13: EMPTY Slot 30: EMPTY

Slot 14: EMPTY Slot 31: EMPTY

Slot 15: EMPTY Slot 32: EMPTY

Slot 16: EMPTY Slot 33: EMPTY

Slot 17: EMPTY Slot 34: EMPTY

Fan Module: Present

Power Supply Module 1: 6160-PEM-DC

Power Supply Module 2: 6160-PEM-DC

dslam02-test.40nr#sh int atm0/1

ATM0/1 is up, line protocol is up

Hardware is ds3suni

MTU 4470 bytes, sub MTU 4470, BW 45000 Kbit, DLY 100 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation ATM, loopback not set

Last input 00:00:00, output 00:00:04, output hang never

Last clearing of "show interface" counters never

Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0

Queueing strategy: fifo

Output queue :0/40 (size/max)

5 minute input rate 3000 bits/sec, 9 packets/sec

5 minute output rate 1000 bits/sec, 1 packets/sec

7673 packets input, 406669 bytes, 0 no buffer

Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

962 packets output, 50986 bytes, 0 underruns

0 output errors, 0 collisions, 0 interface resets

0 output buffer failures, 0 output buffers swapped out

dslam02-test.40nr#sh int atm0/2

ATM0/2 is up, line protocol is up

Hardware is ds3suni

MTU 4470 bytes, sub MTU 4470, BW 45000 Kbit, DLY 100 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation ATM, loopback not set

Last input 00:00:01, output 00:00:01, output hang never

Last clearing of "show interface" counters never

Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0

Queueing strategy: fifo

Output queue :0/40 (size/max)

5 minute input rate 0 bits/sec, 0 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

1293 packets input, 68529 bytes, 0 no buffer

Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

1096 packets output, 58088 bytes, 0 underruns

0 output errors, 0 collisions, 0 interface resets

0 output buffer failures, 0 output buffers swapped out

dslam02-test.40nr#sh log

dslam02-test.40nr#sh logging

Syslog logging: enabled (0 messages dropped, 0 messages rate-limited, 0 flushes, 0 overruns)

Console logging: level debugging, 59 messages logged

Monitor logging: level debugging, 0 messages logged

Buffer logging: level debugging, 59 messages logged

Logging Exception size (4096 bytes)

Trap logging: level informational, 71 message lines logged

Log Buffer (8192 bytes):

00:00:54: %SYS-5-RESTART: System restarted --

Cisco Internetwork Operating System Software

IOS (tm) NI2 Software (NI2-DSL-M), Version 12.2(12)DA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

TAC Support: http://www.cisco.com/tac

Copyright (c) 1986-2003 by cisco Systems, Inc.

Compiled Wed 23-Apr-03 11:55 by torowe

00:00:54: %SNMP-5-COLDSTART: SNMP agent on host dslam02-test.40nr is undergoing a cold start

00:00:54: %LINK-3-UPDOWN: Interface ATM0/0 to ATM0/1, changed state to up

00:00:54: %LINK-3-UPDOWN: Interface ATM0/2 to ATM0/3, changed state to down

00:00:54: %LINK-3-UPDOWN: Interface Ethernet0/0, changed state to up

00:00:54: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0/1, changed state to up

00:00:54: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0/2 to ATM0/3, changed state to down

00:00:54: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0, changed state to up

00:00:54: %SYS-6-BOOTTIME: Time taken to reboot after reload = 946689358 seconds

00:00:56: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/1 to ATM1/8, changed state to down

00:00:56: %ATM-4-ILMICONFIGCHANGE: ILMI(ATM0/1): Restarting ATM signalling and ILMI. Peer Configuration change detected.

00:00:56: %ATM-5-ATMSOFTSTART: Restarting ATM signalling and ILMI on ATM0/1.

00:00:58: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0, changed state to up

00:01:03: %SLOT-3-MODULE_MISSING: ASSERT MAJOR Slot 1 Provisioned slot is empty

00:01:08: %SLOT-3-MODULE_MISSING: CLEAR MAJOR Slot 1 Provisioned slot is empty

00:01:08: %SLOT-3-MODULE_DETECTED: ASSERT INFO Slot 1 Module was detected

00:01:08: %SLOT-3-MODULE_DETECTED: ASSERT INFO Slot 9 Module was detected

00:01:08: %IPCOIR-5-CARD_LOADING: Loading card 9

00:01:08: %SUNI_QJET-3-YEL: CLEAR CRITICAL ATM0/2 Yellow Alarm Received

00:01:11: %LINK-3-UPDOWN: Interface ATM1/1 to ATM1/8, changed state to down

00:01:11: %LINK-3-UPDOWN: Interface ATM0/2, changed state to up

00:01:12: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM9/1 to ATM9/8, changed state to down

00:01:49: %LINK-3-UPDOWN: Interface ATM1/3, changed state to up

00:01:50: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/3, changed state to up

00:02:33: %ATMCORE-3-INTERNAL_ERROR: CTT row 3800 is internally created.

Please do not use this row for creating VCs.

Use only those rows listed in show running-config

00:02:34: %SYS-5-CONFIG_I: Configured from console by vty0 (192.168.11.16)

00:02:39: %CLOCKSW: Switching from System to ATM0/1 at prior 5

00:04:08: %SLOT-3-MODULE_DETECTED: CLEAR INFO Slot 9 Module was detected

00:04:08: %SLOT-3-MODULE_MISSING: ASSERT MAJOR Slot 9 Provisioned slot is empty

00:04:29: %SLOT-3-MODULE_MISSING: CLEAR MAJOR Slot 9 Provisioned slot is empty

00:04:29: %SLOT-3-MODULE_DETECTED: ASSERT INFO Slot 9 Module was detected

00:04:32: %LINK-3-UPDOWN: Interface ATM9/1 to ATM9/8, changed state to down

00:07:41: %SLOT-3-MODULE_DETECTED: CLEAR INFO Slot 9 Module was detected

00:07:41: %SLOT-3-MODULE_MISSING: ASSERT MAJOR Slot 9 Provisioned slot is empty

00:07:42: %SLOT-3-MODULE_DETECTED: CLEAR INFO Slot 1 Module was detected

00:07:42: %SLOT-3-MODULE_MISSING: ASSERT MAJOR Slot 1 Provisioned slot is empty

00:07:44: %LINK-5-CHANGED: Interface ATM9/1 to ATM9/8, changed state to initializing

00:07:45: %LINK-5-CHANGED: Interface ATM1/1 to ATM1/8, changed state to initializing

00:07:46: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/3, changed state to down

00:08:13: %SLOT-3-MODULE_MISSING: CLEAR MAJOR Slot 1 Provisioned slot is empty

00:08:13: %SLOT-3-MODULE_DETECTED: ASSERT INFO Slot 1 Module was detected

00:08:16: %LINK-3-UPDOWN: Interface ATM1/1 to ATM1/8, changed state to down

00:08:55: %LINK-3-UPDOWN: Interface ATM1/3, changed state to up

00:08:56: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/3, changed state to up

00:09:21: %SLOT-3-MODULE_MISSING: CLEAR MAJOR Slot 9 Provisioned slot is empty

00:09:21: %SLOT-3-MODULE_DETECTED: ASSERT INFO Slot 9 Module was detected

00:09:24: %LINK-3-UPDOWN: Interface ATM9/1 to ATM9/8, changed state to down

00:10:14: %ATMCORE-3-INTERNAL_ERROR: CTT row 3800 is internally created.

Please do not use this row for creating VCs.

Use only those rows listed in show running-config

00:10:15: %SYS-5-CONFIG_I: Configured from console by vty0 (192.168.11.16)

00:10:33: %ATMCORE-3-INTERNAL_ERROR: CTT row 3800 is internally created.

Please do not use this row for creating VCs.

Use only those rows listed in show running-config

dslam02-test.40nr#

Thank you,

Mihai

1 REPLY
Bronze

Re: 00:10:33: %ATMCORE-3-INTERNAL_ERROR: CTT row 3800 is interna

This is what seems to be the explanation for the message : "The ATM core subsystem has encountered an internal software error. The error message contains text that can be used to help identify the nature of the problem".

162
Views
0
Helpful
1
Replies