09-12-2002 05:28 AM - edited 03-02-2019 01:19 AM
Hi everybody,
i have an 1760 with two WIC-1B-S/T and 12.2(7.1)T. I have configured both BRI's as "dialer pool-member 1". When connecting the ISDN NT to bri1/0 the Dialer brings up the interface and everything's fine. When connecting the ISDN NT to bri0/0 the Dialer still trys to bring up bri1/0 and no call is beeing set up. It's only a test, but in the event of an failure of bri1/0 i would get no connection over the functioning bri0/0.
Thank's for any help
09-17-2002 01:13 PM
First of, the Dialer should only consider those ISDN interfaces whose layer1 us UP. If you only have one interface that is UP, that interface should be dialing. If there are multiple interfaces which are UP, and neither has a configured priority higher than the other (an option with the "dialer pool" command), then the first physical interface (0/0 in your case) will always be attempted first. If there is a priority configured, the one with the highest priority will always be used first. Note that, as an aside, there is no need to use dialer profiles unless you will be connecting to different remote sites and need different configuration characterstics for each remote site. Otherwise, regular DDR should be fine (configure a dialer rotary group and place each BRI in the rotary group) and is likely easier to configure.
To troubleshoot your problem when connected to 0/0, you should ensure that 0/0 is UP (sh isdn status), and then have a look at "debug isdn q931" and "debug dialer" to see what's going on during the call attempt.
09-19-2002 03:40 AM
Thanks for your response. Here's some more information. Now I tried using rotary-group and got the same result. Please see the "sh isdn status" output as well as the configuration and debugging:
nst40-r-malu40#sh isdn stat
Global ISDN Switchtype = basic-net3
ISDN BRI0/0 interface
dsl 0, interface ISDN Switchtype = basic-net3
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 69, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 0 CCBs = 0
The Free Channel Mask: 0x80000003
Number of L2 Discards = 0, L2 Session ID = 6
ISDN BRI1/0 interface
dsl 1, interface ISDN Switchtype = basic-net3
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
Layer 2 NOT Activated
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 1 CCBs = 0
The Free Channel Mask: 0x80000003
Number of L2 Discards = 0, L2 Session ID = 90
Total Allocated ISDN CCBs = 0
nst40-r-malu40#
nst40-r-malu40#
nst40-r-malu40#
nst40-r-malu40#
nst40-r-malu40#
nst40-r-malu40#
nst40-r-malu40#ping 10.10.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.10.1.1, timeout is 2 seconds:
*Mar 1 21:09:23 UTC: BR1/0 DDR: rotor dialout [priority]
*Mar 1 21:09:23 UTC: BR1/0 DDR: Dialing cause ip (s=192.168.1.4, d=10.10.1.1)
*Mar 1 21:09:23 UTC: BR1/0 DDR: Attempting to dial 1866
*Mar 1 21:09:23 UTC: ISDN BR1/0 EVENT: UserIdle: callid 0x8032 received ISDN_CA
LL (0x0)
*Mar 1 21:09:23 UTC: ISDN **ERROR**: Module-lif Function-LIF_AddTimer Error-
Unknown Class.
*Mar 1 21:09:23 UTC: ISDN **ERROR**: Module-lif Function-LIF_AddTimer Error-
Unknown Class.
*Mar 1 21:09:23 UTC: ISDN **ERROR**: Module-lif Function-LIF_AddTimer Error-
Unknown Class.
*Mar 1 21:09:23 UTC: ISDN BR1/0 EVENT: handle_l2d_srq_mail: Activating Layer 1
*Mar 1 21:09:23 UTC: ISDN BR1/0 EVENT: isdn_sw_cstate: State = 4, Old State = 4
.
*Mar 1 21:09:24 UTC: ISDN BR1/0 EVENT: handle_l2d_srq_mail: Layer 1 not Active
after T3 delay
*Mar 1 21:09:24 UTC: BRI1/0: wait for isdn carrier timeout, call id=0x8032
*Mar 1 21:09:24 UTC: ISDN **ERROR**: LIF_RemoveTimer Timer class 1 UNKNOWN
*Mar 1 21:09:24 UTC: ISDN **ERROR**: LIF_RemoveTimer Timer class 1 UNKNOWN
*Mar 1 21:09:24 UTC: ISDN **ERROR**: LIF_RemoveTimer Timer class 1 UNKNOWN
*Mar 1 21:09:25 UTC: ISDN BR1/0 EVENT: process_rxstate: ces/callid 1/0x8032 cal
ltype 1 HOST_DISCONNECT_ACK
*Mar 1 21:09:25 UTC: ISDN BR1/0 **ERROR**: host_disconnect_ack: Unfound B-chann
el on Disconnect_Ack call id 0x8032
*Mar 1 21:09:25 UTC: BR1/0 DDR: rotor dialout [priority]
*Mar 1 21:09:25 UTC: BR1/0 DDR: Dialing cause ip (s=192.168.1.4, d=10.10.1.1)
*Mar 1 21:09:25 UTC: BR1/0 DDR: Attempting to dial 1866
*Mar 1 21:09:25 UTC: ISDN BR1/0 EVENT: UserIdle: callid 0x8033 received ISDN_CA
LL (0x0)
*Mar 1 21:09:25 UTC: ISDN **ERROR**: Module-lif Function-LIF_AddTimer Error-
Unknown Class.
*Mar 1 21:09:25 UTC: ISDN **ERROR**: Module-lif Function-LIF_AddTimer Error-
Unknown Class.
*Mar 1 21:09:25 UTC: ISDN **ERROR**: Module-lif Function-LIF_AddTimer Error-
Unknown Class.
*Mar 1 21:09:25 UTC: ISDN BR1/0 EVENT: handle_l2d_srq_mail: Activating Layer 1.
*Mar 1 21:09:27 UTC: ISDN BR1/0 EVENT: handle_l2d_srq_mail: Layer 1 not Active
after T3 delay
*Mar 1 21:09:27 UTC: BRI1/0: wait for isdn carrier timeout, call id=0x8033
*Mar 1 21:09:27 UTC: ISDN **ERROR**: LIF_RemoveTimer Timer class 1 UNKNOWN
*Mar 1 21:09:27 UTC: ISDN **ERROR**: LIF_RemoveTimer Timer class 1 UNKNOWN
*Mar 1 21:09:27 UTC: ISDN **ERROR**: LIF_RemoveTimer Timer class 1 UNKNOWN
*Mar 1 21:09:27 UTC: ISDN BR1/0 EVENT: process_rxstate: ces/callid 1/0x8033 cal
ltype 1 HOST_DISCONNECT_ACK
*Mar 1 21:09:27 UTC: ISDN BR1/0 **ERROR**: host_disconnect_ack: Unfound B-chann
el on Disconnect_Ack call id 0x8033
*Mar 1 21:09:27 UTC: ISDN BR1/0 EVENT: handle_l2d_srq_mail: Activating Layer 1.
*Mar 1 21:09:29 UTC: BR1/0 DDR: rotor dialout [priority]
*Mar 1 21:09:29 UTC: BR1/0 DDR: Dialing cause ip (s=192.168.1.4, d=10.10.1.1)
*Mar 1 21:09:29 UTC: BR1/0 DDR: Attempting to dial 1866
*Mar 1 21:09:29 UTC: ISDN BR1/0 EVENT: UserIdle: callid 0x8034 received ISDN_CA
LL (0x0)
*Mar 1 21:09:29 UTC: ISDN **ERROR**: Module-lif Function-LIF_AddTimer Error-
Unknown Class.
*Mar 1 21:09:29 UTC: ISDN **ERROR**: Module-lif Function-LIF_AddTimer Error-
Unknown Class.
*Mar 1 21:09:29 UTC: ISDN **ERROR**: Module-lif Function-LIF_AddTimer Error-
Unknown Class.
*Mar 1 21:09:29 UTC: ISDN BR1/0 EVENT: handle_l2d_srq_mail: Layer 1 not Active
after T3 delay
*Mar 1 21:09:29 UTC: BRI1/0: wait for isdn carrier timeout, call id=0x8034
*Mar 1 21:09:29 UTC: ISDN **ERROR**: LIF_RemoveTimer Timer class 1 UNKNOWN
*Mar 1 21:09:29 UTC: ISDN **ERROR**: LIF_RemoveTimer Timer class 1 UNKNOWN
*Mar 1 21:09:29 UTC: ISDN **ERROR**: LIF_RemoveTimer Timer class 1 UNKNOWN
*Mar 1 21:09:29 UTC: ISDN BR1/0 EVENT: process_rxstate: ces/callid 1/0x8034 cal
ltype 1 HOST_DISCONNECT_ACK
*Mar 1 21:09:29 UTC: ISDN BR1/0 **ERROR**: host_disconnect_ack: Unfound B-chann
el on Disconnect_Ack call id 0x8034.
*Mar 1 21:09:31 UTC: BR1/0 DDR: rotor dialout [priority]
*Mar 1 21:09:31 UTC: BR1/0 DDR: Dialing cause ip (s=192.168.1.4, d=10.10.1.1)
*Mar 1 21:09:31 UTC: BR1/0 DDR: Attempting to dial 1866
*Mar 1 21:09:31 UTC: ISDN BR1/0 EVENT: UserIdle: callid 0x8035 received ISDN_CA
LL (0x0)
*Mar 1 21:09:31 UTC: ISDN **ERROR**: Module-lif Function-LIF_AddTimer Error-
Unknown Class.
*Mar 1 21:09:31 UTC: ISDN **ERROR**: Module-lif Function-LIF_AddTimer Error-
Unknown Class.
*Mar 1 21:09:31 UTC: ISDN **ERROR**: Module-lif Function-LIF_AddTimer Error-
Unknown Class.
*Mar 1 21:09:31 UTC: ISDN BR1/0 EVENT: handle_l2d_srq_mail: Activating Layer 1
*Mar 1 21:09:31 UTC: ISDN BR1/0 EVENT: service_queue_from_physical_layer: Recvd
L1 prim 3 state is 0
*Mar 1 21:09:31 UTC: BRI1/0: wait for isdn carrier timeout, call id=0x8035
*Mar 1 21:09:31 UTC: ISDN BR1/0 EVENT: isdn_sw_cstate: State = 0, Old State = 4
*Mar 1 21:09:31 UTC: ISDN BR1/0 EVENT: handle_l2d_srq_mail: Layer 1 not Active
after T3 delay
*Mar 1 21:09:31 UTC: ISDN **ERROR**: LIF_RemoveTimer Timer class 1 UNKNOWN
*Mar 1 21:09:31 UTC: ISDN **ERROR**: LIF_RemoveTimer Timer class 1 UNKNOWN
*Mar 1 21:09:31 UTC: ISDN **ERROR**: LIF_RemoveTimer Timer class 1 UNKNOWN
*Mar 1 21:09:31 UTC: ISDN BR1/0 EVENT: process_rxstate: ces/callid 1/0x8035 cal
ltype 1 HOST_DISCONNECT_ACK
*Mar 1 21:09:31 UTC: ISDN BR1/0 **ERROR**: host_disconnect_ack: Unfound B-chann
el on Disconnect_Ack call id 0x8035.
Success rate is 0 percent (0/5)
nst40-r-malu40#
nst40-r-malu40#
nst40-r-malu40#sh run
...
isdn switch-type basic-net3
!
!
!
interface FastEthernet0/0
ip address 172.17.184.10 255.255.248.0
speed auto
no cdp enable
!
interface BRI0/0
no ip address
encapsulation ppp
dialer rotary-group 1
dialer priority 10
dialer-group 5
isdn switch-type basic-net3
no cdp enable
ppp authentication chap
ppp multilink
!
interface BRI1/0
no ip address
encapsulation ppp
dialer rotary-group 1
dialer priority 10
dialer-group 5
isdn switch-type basic-net3
no cdp enable
ppp authentication chap
ppp multilink
!
interface Dialer1
description "ppp Einwahl Interface nach Mannheim"
ip address 192.168.1.4 255.255.255.0
encapsulation ppp
dialer in-band
dialer map ip 192.168.1.1 1866
dialer map ip 192.168.1.2 1866
dialer-group 5
no cdp enable
ppp authentication chap pap
ppp multilink
multilink max-links 4
!
ip classless
ip route 10.3.0.0 255.255.0.0 Dialer1
ip route 10.3.0.0 255.255.0.0 192.168.1.2
ip route 10.10.0.0 255.255.0.0 192.168.1.1
no ip http server
!
!
dialer-list 5 protocol ip permit
no cdp run
!
line con 0
exec-timeout 0 0
login local
line aux 0
line vty 0 4
login local
!
end
09-19-2002 09:13 AM
Can you try removing the "dialer priority" commands from the BRI's? If the problem persists, then please try saving the config and reloading the router. If the problem *still* persists, then try "dialer rotor best" under the dialer interface. Thanks.
09-19-2002 10:49 PM
I tried without "dialer priority" before. Reboot didn't help.
"dialer rotor best" solved the problem!!
Thank you
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide