03-29-2004 12:03 AM - edited 03-02-2019 02:36 PM
how to config 2 64k customer on a singel isdn line,
ie to make use of the 1st B channel for one customer & 2nd B channel for another customer
I think this is the config , but some minor error are there, any light on this
interface BRI 1/0
ip unnumbered FastEthernet0/0
encapsulation ppp
dialer pool-member 10 max-link 1
dialer pool-member 20 max-link 1
isdn switch-type basic-net3
no cdp enable
ppp authentication pap
ppp multilink
end
!
interface Dialer1
ip unnumbered FastEthernet0/0
encapsulation ppp
dialer pool 10
no cdp enable
ppp authentication pap
!
interface Dialer2
ip unnumbered FastEthernet0/0
encapsulation ppp
dialer pool 20
no cdp enable
ppp authentication pap
03-29-2004 05:19 AM
Hello,
I have marked the additions with:
-->
and the information to be removed with:
--<
I would take ppp multilink out of the configuration alltogether, since you have only two B-channels for two customers.
Also, don´t forget your static routes.
interface BRI 1/0
ip unnumbered FastEthernet0/0
encapsulation ppp
dialer pool-member 10 max-link 1
dialer pool-member 20 max-link 1
isdn switch-type basic-net3
no cdp enable
ppp authentication pap
--
end
!
interface Dialer1
ip unnumbered FastEthernet0/0
encapsulation ppp
dialer pool 10
-->dialer-group 1
-->dialer remote-name xxxx
-->dialer string xxxxxxxx
no cdp enable
ppp authentication pap
!
interface Dialer2
ip unnumbered FastEthernet0/0
encapsulation ppp
dialer pool 20
-->dialer-group 1
-->dialer remote-name xxxx
-->dialer string xxxxxxxx
no cdp enable
ppp authentication pap
!
-->dialer-list 1 protocol ip permit
HTH,
Georg
03-29-2004 09:00 PM
changed the config, still the same problems, (the router accepts calls & no outgoing calls, so dialer string etc not required )
this is the config
interface BRI1/3
no ip address
encapsulation ppp
dialer pool-member 10 max-link 1
dialer pool-member 20 max-link 1
isdn switch-type basic-net3
no cdp enable
ppp authentication pap
end
!
interface Dialer1
ip unnumbered FastEthernet0/0
encapsulation ppp
dialer pool 10
no cdp enable
ppp authentication pap
!
interface Dialer2
ip unnumbered FastEthernet0/0
encapsulation ppp
dialer pool 20
no cdp enable
ppp authentication pap
& this is the debug output
37.020 : ISDN BR1/3: LIF_EVENT: ces/callid 1/0x5A9 HOST_CONNECT
37.020 : ISDN BR1/3: Event: Connected to xxxxxxxx on B1 at 64 Kb/s
42.600 : %ISDN-6-CONNECT: Interface BRI1/3:1 is now connected to xxxxxxxx
56.996 : ISDN BR1/3: Event: Hangup call to call id 0x5A9
56.996 : ISDN BR1/3: process_disconnect(): call id 0x5A9, call type is DATA, b_idb 0x6274DED0, ces 1, cause Normal call clearing(0x10)
56.996 : %ISDN-6-DISCONNECT: Interface BRI1/3:1 disconnected from xxxxxxxx testacct, call lasted 20 seconds
56.996 : ISDN: get_isdn_service_state(): idb 0x6274DED0 bchan 2 is_isdn 1 Not a Pri
56.996 : CCBRI_Go Fr Host InPkgInfo (Len=13) :
56.996 : 5 3 1 5 A9 3 8 1 90 8 2 80 90
56.996 :
57.260 : CCBRI_Go Fr L3 pkt (Len=4) :
57.260 : 4D 1 B4 97
57.264 :
57.264 : ISDN BR1/3: LIF_EVENT: ces/callid 1/0x5A9 HOST_DISCONNECT_ACK
57.264 : ISDN: get_isdn_service_state(): idb 0x6274DED0 bchan 2 is_isdn 1 Not a Pri
57.264 : ISDN BR1/3: HOST_DISCONNECT_ACK: call type is DATA
57.264 : %LINK-3-UPDOWN: Interface BRI1/3:1, changed state to down
59.360 : %ISDN-6-LAYER2DOWN: Layer 2 for Interface BR1/3, TEI 114 changed to down
01.228 : CCBRI_Go Fr L3 pkt (Len=33) :
01.228 : 5 1 B5 90 A1 4 2 88 90 18 1 89 6C C 21 83 34 36 31 32 33 35 34 34 32 33 70 5 81 39 35 33 35
01.228 :
01.228 : ISDN BR1/3: Incoming call id = 0x05AA, dsl 3
01.228 : ISDN BR1/3: LIF_EVENT: ces/callid 1/0x5AA HOST_INCOMING_CALL
01.228 : ISDN BR1/3: HOST_INCOMING_CALL: (non-POTS) DATA
01.228 : ISDN BR1/3: HOST_INCOMING_CALL: (1) call_type = DATA
01.228 : ISDN BR1/3: HOST_INCOMING_CALL: voice_answer_data = FALSE call type is DATA
01.228 : %DIALER-6-BIND: Interface BR1/3:1 bound to profile Di2
01.228 : ISDN BR1/3: RM returned call_type 0 resource type 0 response 1
01.228 : CCBRI_Go Fr Host InPkgInfo (Len=9) :
01.228 : 7 3 1 5 AA 3 18 1 89
01.228 :
01.228 : ISDN BR1/3: isdn_send_connect(): msg 4, call id 0x5AA, ces 1 bchan 0, call type DATA
01.232 : %LINK-3-UPDOWN: Interface BRI1/3:1, changed state to up
01.232 : ISDN: get_isdn_service_state(): idb 0x6274DED0 bchan 2 is_isdn 1 Not a Pri
01.232 : CCBRI_Go Fr Host InPkgInfo (Len=6) :
01.232 : 4 3 1 5 AA 0
01.232 :
01.256 : %ISDN-6-LAYER2UP: Layer 2 for Interface BR1/3, TEI 114 changed to up
01.732 : CCBRI_Go Fr L3 pkt (Len=4) :
01.732 : F 1 B5 92
01.732 :
01.732 : ISDN BR1/3: LIF_EVENT: ces/callid 1/0x5AA HOST_CONNECT
01.732 : ISDN BR1/3: Event: Connected to xxxxxxxx on B1 at 64 Kb/s
07.232 : %ISDN-6-CONNECT: Interface BRI1/3:1 is now connected to xxxxxxxx
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: