cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
282
Views
0
Helpful
2
Replies

2 64K customers on a single isdn line

vinu104
Level 1
Level 1

how to config 2 64k customer on a singel isdn line,

ie to make use of the 1st B channel for one customer & 2nd B channel for another customer

I think this is the config , but some minor error are there, any light on this

interface BRI 1/0

ip unnumbered FastEthernet0/0

encapsulation ppp

dialer pool-member 10 max-link 1

dialer pool-member 20 max-link 1

isdn switch-type basic-net3

no cdp enable

ppp authentication pap

ppp multilink

end

!

interface Dialer1

ip unnumbered FastEthernet0/0

encapsulation ppp

dialer pool 10

no cdp enable

ppp authentication pap

!

interface Dialer2

ip unnumbered FastEthernet0/0

encapsulation ppp

dialer pool 20

no cdp enable

ppp authentication pap

2 Replies 2

Hello,

I have marked the additions with:

-->

and the information to be removed with:

--<

I would take ppp multilink out of the configuration alltogether, since you have only two B-channels for two customers.

Also, don´t forget your static routes.

interface BRI 1/0

ip unnumbered FastEthernet0/0

encapsulation ppp

dialer pool-member 10 max-link 1

dialer pool-member 20 max-link 1

isdn switch-type basic-net3

no cdp enable

ppp authentication pap

--

end

!

interface Dialer1

ip unnumbered FastEthernet0/0

encapsulation ppp

dialer pool 10

-->dialer-group 1

-->dialer remote-name xxxx

-->dialer string xxxxxxxx

no cdp enable

ppp authentication pap

!

interface Dialer2

ip unnumbered FastEthernet0/0

encapsulation ppp

dialer pool 20

-->dialer-group 1

-->dialer remote-name xxxx

-->dialer string xxxxxxxx

no cdp enable

ppp authentication pap

!

-->dialer-list 1 protocol ip permit

HTH,

Georg

changed the config, still the same problems, (the router accepts calls & no outgoing calls, so dialer string etc not required )

this is the config

interface BRI1/3

no ip address

encapsulation ppp

dialer pool-member 10 max-link 1

dialer pool-member 20 max-link 1

isdn switch-type basic-net3

no cdp enable

ppp authentication pap

end

!

interface Dialer1

ip unnumbered FastEthernet0/0

encapsulation ppp

dialer pool 10

no cdp enable

ppp authentication pap

!

interface Dialer2

ip unnumbered FastEthernet0/0

encapsulation ppp

dialer pool 20

no cdp enable

ppp authentication pap

& this is the debug output

37.020 : ISDN BR1/3: LIF_EVENT: ces/callid 1/0x5A9 HOST_CONNECT

37.020 : ISDN BR1/3: Event: Connected to xxxxxxxx on B1 at 64 Kb/s

42.600 : %ISDN-6-CONNECT: Interface BRI1/3:1 is now connected to xxxxxxxx

56.996 : ISDN BR1/3: Event: Hangup call to call id 0x5A9

56.996 : ISDN BR1/3: process_disconnect(): call id 0x5A9, call type is DATA, b_idb 0x6274DED0, ces 1, cause Normal call clearing(0x10)

56.996 : %ISDN-6-DISCONNECT: Interface BRI1/3:1 disconnected from xxxxxxxx testacct, call lasted 20 seconds

56.996 : ISDN: get_isdn_service_state(): idb 0x6274DED0 bchan 2 is_isdn 1 Not a Pri

56.996 : CCBRI_Go Fr Host InPkgInfo (Len=13) :

56.996 : 5 3 1 5 A9 3 8 1 90 8 2 80 90

56.996 :

57.260 : CCBRI_Go Fr L3 pkt (Len=4) :

57.260 : 4D 1 B4 97

57.264 :

57.264 : ISDN BR1/3: LIF_EVENT: ces/callid 1/0x5A9 HOST_DISCONNECT_ACK

57.264 : ISDN: get_isdn_service_state(): idb 0x6274DED0 bchan 2 is_isdn 1 Not a Pri

57.264 : ISDN BR1/3: HOST_DISCONNECT_ACK: call type is DATA

57.264 : %LINK-3-UPDOWN: Interface BRI1/3:1, changed state to down

59.360 : %ISDN-6-LAYER2DOWN: Layer 2 for Interface BR1/3, TEI 114 changed to down

01.228 : CCBRI_Go Fr L3 pkt (Len=33) :

01.228 : 5 1 B5 90 A1 4 2 88 90 18 1 89 6C C 21 83 34 36 31 32 33 35 34 34 32 33 70 5 81 39 35 33 35

01.228 :

01.228 : ISDN BR1/3: Incoming call id = 0x05AA, dsl 3

01.228 : ISDN BR1/3: LIF_EVENT: ces/callid 1/0x5AA HOST_INCOMING_CALL

01.228 : ISDN BR1/3: HOST_INCOMING_CALL: (non-POTS) DATA

01.228 : ISDN BR1/3: HOST_INCOMING_CALL: (1) call_type = DATA

01.228 : ISDN BR1/3: HOST_INCOMING_CALL: voice_answer_data = FALSE call type is DATA

01.228 : %DIALER-6-BIND: Interface BR1/3:1 bound to profile Di2

01.228 : ISDN BR1/3: RM returned call_type 0 resource type 0 response 1

01.228 : CCBRI_Go Fr Host InPkgInfo (Len=9) :

01.228 : 7 3 1 5 AA 3 18 1 89

01.228 :

01.228 : ISDN BR1/3: isdn_send_connect(): msg 4, call id 0x5AA, ces 1 bchan 0, call type DATA

01.232 : %LINK-3-UPDOWN: Interface BRI1/3:1, changed state to up

01.232 : ISDN: get_isdn_service_state(): idb 0x6274DED0 bchan 2 is_isdn 1 Not a Pri

01.232 : CCBRI_Go Fr Host InPkgInfo (Len=6) :

01.232 : 4 3 1 5 AA 0

01.232 :

01.256 : %ISDN-6-LAYER2UP: Layer 2 for Interface BR1/3, TEI 114 changed to up

01.732 : CCBRI_Go Fr L3 pkt (Len=4) :

01.732 : F 1 B5 92

01.732 :

01.732 : ISDN BR1/3: LIF_EVENT: ces/callid 1/0x5AA HOST_CONNECT

01.732 : ISDN BR1/3: Event: Connected to xxxxxxxx on B1 at 64 Kb/s

07.232 : %ISDN-6-CONNECT: Interface BRI1/3:1 is now connected to xxxxxxxx

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: