Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

24w1d: %POT1E1-3-FWFATAL

Can someone explain this error message???

24w1d: POT1E1 (bay 2) SW_WatchDog not cleared, SW_WatchDog = 33

24w1d: %POT1E1-3-FWFATAL: Bay 2: firmware needs reset due to fatal

software

erro

rs

24w1d: % 0x080 0x00000000 0x00000000 0x00000000

24w1d: % 0x080 0x00000000 0x00000000 0x00012950

24w1d: % 0x087 0x00000001 0x0007FF98 0x00001FFF

24w1d: % 0x087 0x00000002 0xFF000000 0x00000007

24w1d: % 0x0815500 0x30000980 0x00000010 0x00000000

24w1d: % 0x08F0F74A55 0x00023FFC 0xFFF01CC0 0x00000000

24w1d: % 0x080 0x00000000 0x00000000 0x00000000

24w1d: % 0x080 0xFF000000 0x00000000 0x00000000

24w1d: % 0x080 0x00000000 0x00000000 0x00000000

24w1d: % 0x088 0x0007FFA8 0x0000F480 0x00002000

24w1d: % 0x0820000 0x00000000 0x00009000 0x48000020

24w1d: % 0x081 0x00000000 0x20000000 0x7FFFFFFF

24w1d: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0:4,

changed

stat

e to up

24w1d: %ALIGN-3-TRACE: -Traceback= 60481FA0 6048434C 60484410 00000000

00000000

00000000 00000000 00000000

24w1d: %ALIGN-3-TRACE: -Traceback= 60481FA4 6048434C 60484410 00000000

00000000

00000000 00000000 00000000

Receiver has loss of frame

Transmitter is sending remote alarm

1 REPLY
Silver

Re: 24w1d: %POT1E1-3-FWFATAL

The root cause of the problem

has been found to be the means that the CPU access memory.

Most likely this is a bug

CSCdv40244: %POT1E1-3-FWFATAL error appears

Tracebacks cannot be decoded without knowing that image you are running. The above defects are fixed in the following releases.

12.2(08)MC02 12.2(10b) 12.1(12.05)E 12.0(21)ST03 12.2(11.04)DA 12.1(06)EZ07 12.0(19)S03 12.2(08)T05 12.0(21)S03 12.2(10.07)S 12.2(10.07)PI05 12.2(10.07)T

12.0(21.03)SY01 012.002(010.007) 12.2(07c) 12.0(21.03)S01 012.001(014.005)

If you are running a code before the above I would recommend changing to something that has this fix.

Hope this helps,

Don

221
Views
0
Helpful
1
Replies
CreatePlease login to create content