06-19-2002 06:51 PM - edited 03-01-2019 10:17 PM
I have this problem when I config it. I don't know where is the mistake. Could you help me? That's very clament!!
Building configuration...
Current configuration:
!
version 12.0
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname router
!
enable secret 5 $1$W/vv$ec.iEER5BMUAxN.3EjMk2/
enable password 0 cisco
!
username aaa password 0 aaa
!
!
!
!
ip subnet-zero
no ip domain-lookup
!
!
!
interface FastEthernet0/0
ip address 172.16.10.100 255.255.255.0
no ip directed-broadcast
no ip mroute-cache
speed auto
full-duplex
!
interface Group-Async1
ip unnumbered FastEthernet0/0
no ip directed-broadcast
encapsulation ppp
ip tcp header-compression passive
no ip mroute-cache
async mode interactive
no fair-queue
peer default ip address pool setup_pool
no cdp enable
ppp authentication chap pap callin
group-range 33 40
!
router rip
version 2
network 172.16.10.0
!
ip local pool setup_pool 172.16.10.245 172.16.10.254
ip classless
no ip http server
!
line con 0
exec-timeout 0 0
password cisco
login
transport input none
line 33 40
autoselect during-login
autoselect ppp
login local
modem InOut
transport input all
transport output pad v120 telnet rlogin udptn
stopbits 1
flowcontrol hardware
line aux 0
exec-timeout 0 0
password cisco
login
modem InOut
modem autoconfigure discovery
transport input all
speed 38400
flowcontrol hardware
line vty 0 4
password cisco
login
!
no scheduler allocate
end
06-20-2002 05:59 AM
Config looks fine..We need to see the following debug from the router during call
debug modem
debug ppp authentication
debug ppp negotiation
term mon
Above debug will give us clear idea about whats going on there...Tejal
06-21-2002 06:48 AM
Oh, Thanx first. But tomorrow is Sat. and I have no chance to config the router, because I configed it remotely use aux. And I'll post debug result at Monday, hope can still get your help! Thank you!
06-20-2002 08:26 PM
Try to reduce the "speed" or not to configure the speed in the line interface, check the phone line(try to put a basic phone-to-phone call to know if the line is ready to used). Check the grounding. Oh ye please verify your debug command carefully.
06-21-2002 06:52 AM
I want to receive call use 8am module, and I set speed on my aux port. But I forgot to debug it. That's a terrible thing :) So I'll do it next Monday. Thanx.
06-25-2002 06:09 PM
Dear mate, I have get the debug infomation, I think the problem perhaps is the chap authentication process. And I want your help on edge. Thanx!!
router#
router#
router#
router#sh line
Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
0 CTY - - - - - 0 0 0/0 -
Ready
A 33 TTY - inout - - - 0 0 0/0 -
Ready
I 34 TTY - inout - - - 0 0 0/0 -
Idle
I 35 TTY - inout - - - 0 0 0/0 -
Idle
I 36 TTY - inout - - - 0 0 0/0 -
Idle
I 37 TTY - inout - - - 0 0 0/0 -
Idle
I 38 TTY - inout - - - 0 0 0/0 -
Idle
I 39 TTY - inout - - - 0 0 0/0 -
Idle
I 40 TTY - inout - - - 0 0 0/0 -
Idle
* 65 AUX 115200/115200- inout - - - 0 0 84/564 -
Ready
66 VTY - - - - - 0 0 0/0 -
Idle
--More-- Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
67 VTY - - - - - 0 0 0/0 -
Idle
68 VTY - - - - - 0 0 0/0 -
Idle
69 VTY - - - - - 0 0 0/0 -
Idle
70 VTY - - - - - 0 0 0/0 -
Idle
Line(s) not in async mode -or- with no hardware support:
1-32, 41-64
router#debut g modem
Modem control/process activation debugging is on
router#debug ppp authen
router#debug ppp authentication
PPP authentication debugging is on
router#debug ppp neg
router#debug ppp negotiation
PPP protocol negotiation debugging is on
router#term mon
router#
router#
00:28:56: Modem 1/0 Mcom: in modem state 'Dialing/Answering'
00:28:56: Modem 1/0 Mcom: in modem state 'Incoming ring'
00:28:59: Modem 1/0 Mcom: in modem state 'Waiting for Carrier'
00:29:05: Modem 1/0 Mcom: in modem state 'Connected'
00:29:05: Modem 1/0 Mcom: CONNECT at 300/300(Tx/Rx), BEL103, Normal, None, Answer
00:29:05: TTY33: DSR came up
00:29:05: tty33: Modem: IDLE->(unknown)
00:29:05: TTY33: EXEC creation
00:29:05: TTY33: set timer type 10, 30 seconds
00:29:06: TTY33: Autoselect(2) sample FF
00:29:06: TTY33: Autoselect(2) sample FFFF
00:29:06: TTY33: Autoselect(2) sample FFFFFF
00:29:06: TTY33: Autoselect(2) sample FFFFFFFF
00:29:06: TTY33: Autoselect(2) sample FFFFFFFF
00:29:06: TTY33: Autoselect(2) sample FFFFFFFF
00:29:07: TTY33: Autoselect(2) sample FFFFFFFF
00:29:07: TTY33: Autoselect(2) sample FFFFFFFF
00:29:07: TTY33: Autoselect(2) sample FFFFFFFF
00:29:07: TTY33: Autoselect(2) sample FFFFFFFF
00:29:07: TTY33: Autoselect(2) sample FFFFFFFF
00:29:07: TTY33: Autoselect(2) sample FFFFFFFF
00:29:07: TTY33: Autoselect(2) sample FFFFFFFF
00:29:07: TTY33: Autoselect(2) sample FFFFFFFF
00:29:10: TTY33: Autoselect(2) sample FFFFFF7E
00:29:10: TTY33: Autoselect(2) sample FFFF7EFE
00:29:10: TTY33: Autoselect(2) sample FF7EFE7D
00:29:10: TTY33: Autoselect(2) sample 7EFE7D23
00:29:10: TTY33: set timer type 10, 30 seconds
00:29:10: TTY33: Autoselect(2) sample FE7D23FF
00:29:10: TTY33: Autoselect(2) sample 7D23FFDF
00:29:11: TTY33: Autoselect(2) sample 23FFDFDF
00:29:11: TTY33: Autoselect(2) sample FFDFDFDF
00:29:11: TTY33: Autoselect(2) sample DFDFDFFF
00:29:11: TTY33: Autoselect(2) sample DFDFFFFF
00:29:11: TTY33: Autoselect(2) sample DFFFFFFF
00:29:11: TTY33: Autoselect(2) sample FFFFFFFF
00:29:11: TTY33: Autoselect(2) sample FFFFFFDF
00:29:11: TTY33: Autoselect(2) sample FFFFDFFF
00:29:11: TTY33: Autoselect(2) sample FFDFFFFF
00:29:11: TTY33: Autoselect(2) sample DFFFFFFF
00:29:11: TTY33: Autoselect(2) sample FFFFFFFF
00:29:11: TTY33: Autoselect(2) sample FFFFFFFF
00:29:11: TTY33: Autoselect(2) sample FFFFFFFF
00:29:11: TTY33: Autoselect(2) sample FFFFFFFF
00:29:11: TTY33: Autoselect(2) sample FFFFFFDF
00:29:11: TTY33: Autoselect(2) sample FFFFDFFF
00:29:11: TTY33: Autoselect(2) sample FFDFFFDF
00:29:12: TTY33: Autoselect(2) sample DFFFDFBE
00:29:12: TTY33: Autoselect(2) sample FFDFBEFF
00:29:12: TTY33: Autoselect(2) sample DFBEFFFE
00:29:12: TTY33: Autoselect(2) sample BEFFFEFF
00:29:13: TTY33: Autoselect(2) sample FFFEFFFF
00:29:13: TTY33: Autoselect(2) sample FEFFFFFF
00:29:15: TTY33: Autoselect(2) sample FFFFFFFF
00:29:18: TTY33: Autoselect(2) sample FFFFFFFF
00:29:18: TTY33: Autoselect(2) sample FFFFFF7E
00:29:18: TTY33: Autoselect(2) sample FFFF7EFF
00:29:18: TTY33: Autoselect(2) sample FF7EFF7D
00:29:18: TTY33: Autoselect(2) sample 7EFF7D23
00:29:18: TTY33 Autoselect cmd: ppp negotiate
00:29:18: TTY33: EXEC creation
00:29:18: TTY33: create timer type 1, 600 seconds
00:29:18: TTY33: destroy timer type 1 (OK)
00:29:18: TTY33: destroy timer type 0
00:29:18: As33 IPCP: Install route to 172.16.10.252
00:29:20: %LINK-3-UPDOWN: Interface Async33, changed state to up
00:29:20: As33 PPP: Treating connection as a callin
00:29:20: As33 PPP: Phase is ESTABLISHING, Passive Open
00:29:20: Modem 1/0 Mcom: PPP escape map: Tx map = FFFFFFFF, Rx map = 0
00:29:20: As33 LCP: State is Listen
00:29:22: As33 LCP: TIMEout: State Listen
00:29:22: Modem 1/0 Mcom: PPP escape map: Tx map = FFFFFFFF, Rx map = 0
00:29:22: As33 LCP: O CONFREQ [Listen] id 77 len 25
00:29:22: As33 LCP: ACCM 0x000A0000 (0x0206000A0000)
00:29:22: As33 LCP: AuthProto CHAP (0x0305C22305)
00:29:22: As33 LCP: MagicNumber 0x083C9860 (0x0506083C9860)
00:29:22: As33 LCP: PFC (0x0702)
00:29:22: As33 LCP: ACFC (0x0802)
00:29:24: As33 LCP: TIMEout: State REQsent
00:29:24: As33 LCP: O CONFREQ [REQsent] id 78 len 25
00:29:24: As33 LCP: ACCM 0x000A0000 (0x0206000A0000)
00:29:24: As33 LCP: AuthProto CHAP (0x0305C22305)
00:29:24: As33 LCP: MagicNumber 0x083C9860 (0x0506083C9860)
00:29:24: As33 LCP: PFC (0x0702)
00:29:24: As33 LCP: ACFC (0x0802)
00:29:26: As33 LCP: TIMEout: State REQsent
00:29:26: As33 LCP: O CONFREQ [REQsent] id 79 len 25
00:29:26: As33 LCP: ACCM 0x000A0000 (0x0206000A0000)
00:29:26: As33 LCP: AuthProto CHAP (0x0305C22305)
00:29:26: As33 LCP: MagicNumber 0x083C9860 (0x0506083C9860)
00:29:26: As33 LCP: PFC (0x0702)
00:29:26: As33 LCP: ACFC (0x0802)
00:29:28: As33 LCP: TIMEout: State REQsent
00:29:28: As33 LCP: O CONFREQ [REQsent] id 80 len 25
00:29:28: As33 LCP: ACCM 0x000A0000 (0x0206000A0000)
00:29:28: As33 LCP: AuthProto CHAP (0x0305C22305)
00:29:28: As33 LCP: MagicNumber 0x083C9860 (0x0506083C9860)
00:29:28: As33 LCP: PFC (0x0702)
00:29:28: As33 LCP: ACFC (0x0802)
00:29:30: As33 LCP: TIMEout: State REQsent
00:29:30: As33 LCP: O CONFREQ [REQsent] id 81 len 25
00:29:30: As33 LCP: ACCM 0x000A0000 (0x0206000A0000)
00:29:30: As33 LCP: AuthProto CHAP (0x0305C22305)
00:29:30: As33 LCP: MagicNumber 0x083C9860 (0x0506083C9860)
00:29:30: As33 LCP: PFC (0x0702)
00:29:30: As33 LCP: ACFC (0x0802)
00:29:32: As33 LCP: TIMEout: State REQsent
00:29:32: As33 LCP: O CONFREQ [REQsent] id 82 len 25
00:29:32: As33 LCP: ACCM 0x000A0000 (0x0206000A0000)
00:29:32: As33 LCP: AuthProto CHAP (0x0305C22305)
00:29:32: As33 LCP: MagicNumber 0x083C9860 (0x0506083C9860)
00:29:32: As33 LCP: PFC (0x0702)
00:29:32: As33 LCP: ACFC (0x0802)
00:29:34: As33 LCP: TIMEout: State REQsent
00:29:34: As33 LCP: O CONFREQ [REQsent] id 83 len 25
00:29:34: As33 LCP: ACCM 0x000A0000 (0x0206000A0000)
00:29:34: As33 LCP: AuthProto CHAP (0x0305C22305)
00:29:34: As33 LCP: MagicNumber 0x083C9860 (0x0506083C9860)
00:29:34: As33 LCP: PFC (0x0702)
00:29:34: As33 LCP: ACFC (0x0802)
00:29:36: As33 LCP: TIMEout: State REQsent
00:29:36: As33 LCP: O CONFREQ [REQsent] id 84 len 25
00:29:36: As33 LCP: ACCM 0x000A0000 (0x0206000A0000)
00:29:36: As33 LCP: AuthProto CHAP (0x0305C22305)
00:29:36: As33 LCP: MagicNumber 0x083C9860 (0x0506083C9860)
00:29:36: As33 LCP: PFC (0x0702)
00:29:36: As33 LCP: ACFC (0x0802)
00:29:38: As33 LCP: TIMEout: State REQsent
00:29:38: As33 LCP: O CONFREQ [REQsent] id 85 len 25
00:29:38: As33 LCP: ACCM 0x000A0000 (0x0206000A0000)
00:29:38: As33 LCP: AuthProto CHAP (0x0305C22305)
00:29:38: As33 LCP: MagicNumber 0x083C9860 (0x0506083C9860)
00:29:38: As33 LCP: PFC (0x0702)
00:29:38: As33 LCP: ACFC (0x0802)
00:29:40: As33 LCP: TIMEout: State REQsent
00:29:40: As33 LCP: O CONFREQ [REQsent] id 86 len 25
00:29:40: As33 LCP: ACCM 0x000A0000 (0x0206000A0000)
00:29:40: As33 LCP: AuthProto CHAP (0x0305C22305)
00:29:40: As33 LCP: MagicNumber 0x083C9860 (0x0506083C9860)
00:29:40: As33 LCP: PFC (0x0702)
00:29:40: As33 LCP: ACFC (0x0802)
00:29:42: As33 LCP: TIMEout: State REQsent
00:29:42: As33 LCP: O CONFREQ [REQsent] id 87 len 25
00:29:42: As33 LCP: ACCM 0x000A0000 (0x0206000A0000)
00:29:42: As33 LCP: AuthProto CHAP (0x0305C22305)
00:29:42: As33 LCP: MagicNumber 0x083C9860 (0x0506083C9860)
00:29:42: As33 LCP: PFC (0x0702)
00:29:42: As33 LCP: ACFC (0x0802)
00:29:44: As33 LCP: TIMEout: State REQsent
00:29:44: TTY33: Async Int reset: Dropping DTR
00:29:44: As33 LCP: State is Listen
00:29:44: Modem 1/0 Mcom: in modem state 'Disconnecting'
00:29:44: Modem 1/0 Mcom: DISCONNECT, duration = 00:00:40, reason (0x9) DTR Drop
00:29:45: TTY33: DSR was dropped
00:29:45: tty33: Modem: READY->(unknown)
00:29:45: Modem 1/0 Mcom: in modem state 'Idle'
00:29:46: TTY33: dropping DTR, hanging up
00:29:46: tty33: Modem: HANGUP->(unknown)
00:29:46: %LINK-5-CHANGED: Interface Async33, changed state to reset
00:29:46: As33 LCP: State is Closed
00:29:46: As33 PPP: Phase is DOWN
00:29:47: TTY33: cleanup pending. Delaying DTR
00:29:48: TTY33: cleanup pending. Delaying DTR
00:29:49: TTY33: cleanup pending. Delaying DTR
00:29:49: TTY33: destroy timer type 0
00:29:49: TTY33: destroy timer type 1
00:29:49: TTY33: destroy timer type 3
00:29:49: TTY33: destroy timer type 4
00:29:49: TTY33: destroy timer type 2
00:29:49: Async33: allowing modem_process to continue hangup
00:29:49: As33 IPCP: Remove route to 172.16.10.252
00:29:50: TTY33: restoring DTR
00:29:51: %LINK-3-UPDOWN: Interface Async33, changed state to down
00:29:51: As33 LCP: State is Closed
06-25-2002 08:24 PM
Somhow router is not getting the LCP reply from the other side device..Here is the suggestion
use "Async mode dedicated" under the interface group-async 1 instead of "interactive" and see if that make any difference..Thanks..Tejal
06-25-2002 10:30 PM
other side is PC, use "dialup network".
06-26-2002 06:06 PM
I have change it to "dedicated" ,but it is still can't work. remote PC's error code is 619. and the follow is the debug info. I don't know how to do ........
00:11:23: Modem 1/0 Mcom: in modem state 'Dialing/Answering'
00:11:23: Modem 1/0 Mcom: in modem state 'Incoming ring'
00:11:26: Modem 1/0 Mcom: in modem state 'Waiting for Carrier'
00:12:05: Modem 1/0 Mcom: in modem state 'Connected'
00:12:05: Modem 1/0 Mcom: CONNECT at 300/300(Tx/Rx), BEL103, Normal, None, Answer
00:12:05: TTY33: DSR came up
00:12:05: TTY33: destroy timer type 1
00:12:05: TTY33: destroy timer type 0
00:12:05: tty33: Modem: IDLE->(unknown)
00:12:07: %LINK-3-UPDOWN: Interface Async33, changed state to up
00:12:07: As33 PPP: Treating connection as a callin
00:12:07: As33 PPP: Phase is ESTABLISHING, Passive Open
00:12:07: Modem 1/0 Mcom: PPP escape map: Tx map = FFFFFFFF, Rx map = 0
00:12:07: As33 LCP: State is Listen
00:12:09: As33 LCP: TIMEout: State Listen
00:12:09: Modem 1/0 Mcom: PPP escape map: Tx map = FFFFFFFF, Rx map = 0
00:12:09: As33 LCP: O CONFREQ [Listen] id 23 len 25
00:12:09: As33 LCP: ACCM 0x000A0000 (0x0206000A0000)
00:12:09: As33 LCP: AuthProto CHAP (0x0305C22305)
00:12:09: As33 LCP: MagicNumber 0x082CD466 (0x0506082CD466)
00:12:09: As33 LCP: PFC (0x0702)
00:12:09: As33 LCP: ACFC (0x0802)
00:12:11: As33 LCP: TIMEout: State REQsent
00:12:11: As33 LCP: O CONFREQ [REQsent] id 24 len 25
00:12:11: As33 LCP: ACCM 0x000A0000 (0x0206000A0000)
00:12:11: As33 LCP: AuthProto CHAP (0x0305C22305)
00:12:11: As33 LCP: MagicNumber 0x082CD466 (0x0506082CD466)
00:12:11: As33 LCP: PFC (0x0702)
00:12:11: As33 LCP: ACFC (0x0802)
00:12:13: As33 LCP: TIMEout: State REQsent
00:12:13: As33 LCP: O CONFREQ [REQsent] id 25 len 25
00:12:13: As33 LCP: ACCM 0x000A0000 (0x0206000A0000)
00:12:13: As33 LCP: AuthProto CHAP (0x0305C22305)
00:12:13: As33 LCP: MagicNumber 0x082CD466 (0x0506082CD466)
00:12:13: As33 LCP: PFC (0x0702)
00:12:13: As33 LCP: ACFC (0x0802)
00:12:15: As33 LCP: TIMEout: State REQsent
00:12:15: As33 LCP: O CONFREQ [REQsent] id 26 len 25
00:12:15: As33 LCP: ACCM 0x000A0000 (0x0206000A0000)
00:12:15: As33 LCP: AuthProto CHAP (0x0305C22305)
00:12:15: As33 LCP: MagicNumber 0x082CD466 (0x0506082CD466)
00:12:15: As33 LCP: PFC (0x0702)
00:12:15: As33 LCP: ACFC (0x0802)
00:12:17: As33 LCP: TIMEout: State REQsent
00:12:17: As33 LCP: O CONFREQ [REQsent] id 27 len 25
00:12:17: As33 LCP: ACCM 0x000A0000 (0x0206000A0000)
00:12:17: As33 LCP: AuthProto CHAP (0x0305C22305)
00:12:17: As33 LCP: MagicNumber 0x082CD466 (0x0506082CD466)
00:12:17: As33 LCP: PFC (0x0702)
00:12:17: As33 LCP: ACFC (0x0802)
00:12:19: As33 LCP: TIMEout: State REQsent
00:12:19: As33 LCP: O CONFREQ [REQsent] id 28 len 25
00:12:19: As33 LCP: ACCM 0x000A0000 (0x0206000A0000)
00:12:19: As33 LCP: AuthProto CHAP (0x0305C22305)
00:12:19: As33 LCP: MagicNumber 0x082CD466 (0x0506082CD466)
00:12:19: As33 LCP: PFC (0x0702)
00:12:19: As33 LCP: ACFC (0x0802)
00:12:21: As33 LCP: TIMEout: State REQsent
00:12:21: As33 LCP: O CONFREQ [REQsent] id 29 len 25
00:12:21: As33 LCP: ACCM 0x000A0000 (0x0206000A0000)
00:12:21: As33 LCP: AuthProto CHAP (0x0305C22305)
00:12:21: As33 LCP: MagicNumber 0x082CD466 (0x0506082CD466)
00:12:21: As33 LCP: PFC (0x0702)
00:12:21: As33 LCP: ACFC (0x0802)
00:12:23: As33 LCP: TIMEout: State REQsent
00:12:23: As33 LCP: O CONFREQ [REQsent] id 30 len 25
00:12:23: As33 LCP: ACCM 0x000A0000 (0x0206000A0000)
00:12:23: As33 LCP: AuthProto CHAP (0x0305C22305)
00:12:23: As33 LCP: MagicNumber 0x082CD466 (0x0506082CD466)
00:12:23: As33 LCP: PFC (0x0702)
00:12:23: As33 LCP: ACFC (0x0802)
00:12:25: As33 LCP: TIMEout: State REQsent
00:12:25: As33 LCP: O CONFREQ [REQsent] id 31 len 25
00:12:25: As33 LCP: ACCM 0x000A0000 (0x0206000A0000)
00:12:25: As33 LCP: AuthProto CHAP (0x0305C22305)
00:12:25: As33 LCP: MagicNumber 0x082CD466 (0x0506082CD466)
00:12:25: As33 LCP: PFC (0x0702)
00:12:25: As33 LCP: ACFC (0x0802)
00:12:27: As33 LCP: TIMEout: State REQsent
00:12:27: As33 LCP: O CONFREQ [REQsent] id 32 len 25
00:12:27: As33 LCP: ACCM 0x000A0000 (0x0206000A0000)
00:12:27: As33 LCP: AuthProto CHAP (0x0305C22305)
00:12:27: As33 LCP: MagicNumber 0x082CD466 (0x0506082CD466)
00:12:27: As33 LCP: PFC (0x0702)
00:12:27: As33 LCP: ACFC (0x0802)
00:12:29: As33 LCP: TIMEout: State REQsent
00:12:29: As33 LCP: O CONFREQ [REQsent] id 33 len 25
00:12:29: As33 LCP: ACCM 0x000A0000 (0x0206000A0000)
00:12:29: As33 LCP: AuthProto CHAP (0x0305C22305)
00:12:29: As33 LCP: MagicNumber 0x082CD466 (0x0506082CD466)
00:12:29: As33 LCP: PFC (0x0702)
00:12:29: As33 LCP: ACFC (0x0802)
00:12:31: As33 LCP: TIMEout: State REQsent
00:12:31: TTY33: Async Int reset: Dropping DTR
00:12:31: As33 LCP: State is Listen
00:12:31: Modem 1/0 Mcom: in modem state 'Disconnecting'
00:12:31: Modem 1/0 Mcom: DISCONNECT, duration = 00:00:26, reason (0x9) DTR Drop
00:12:32: Modem 1/0 Mcom: in modem state 'Idle'
00:12:32: TTY33: DSR was dropped
00:12:32: tty33: Modem: READY->(unknown)
00:12:33: %LINK-5-CHANGED: Interface Async33, changed state to reset
00:12:33: As33 LCP: State is Closed
00:12:33: As33 PPP: Phase is DOWN
00:12:33: TTY33: dropping DTR, hanging up
00:12:33: tty33: Modem: HANGUP->(unknown)
00:12:34: TTY33: cleanup pending. Delaying DTR
00:12:35: TTY33: cleanup pending. Delaying DTR
00:12:36: TTY33: destroy timer type 0
00:12:36: TTY33: destroy timer type 1
00:12:36: TTY33: destroy timer type 3
00:12:36: TTY33: destroy timer type 4
00:12:36: TTY33: destroy timer type 2
00:12:36: Async33: allowing modem_process to continue hangup
00:12:37: TTY33: restoring DTR
00:12:38: %LINK-3-UPDOWN: Interface Async33, changed state to down
00:12:38: As33 LCP: State is Closed
06-30-2002 12:54 AM
I don't know if it is pressed for "modem autoconfigure discovery" in the line 33 to 40
06-30-2002 12:56 AM
And I havn't grounding the device. Someone told me 8am is a grounding sensitivity module. Who could tell me if it is a important factor?
06-30-2002 10:00 AM
The previous two debugs indicate the call connected only at BEL103 (300 baud)....try forcing to v.34:
configure terminal
modemcap edit V34_ONLY misc &F%L0
line 33 40
modem autoconfigure type V34_ONLY
Also can you try moving the PSTN line to another modem port, say 34 or changing the line itself.
Yes, the chassis needs to be grounded .....please refer to Field Notice to this effect:
http://www-tac/Support_Library/field_alerts/fn8771.html
Thanks, Mak.
07-01-2002 05:55 AM
Can I type "modem autoconfigure discovery" instead "modem autoconfigure type V34_ONLY"? And if I can use it , should I still type "modemcap edit V34_ONLY misc &F%L0"???
07-01-2002 08:48 AM
You can with the "modem autoconfig discovery" , without the "modem autoconfigure type V34_ONLY" (IOS trying to detect the external modem connected)....if that does not work, try locking to v.34.
Also as per the previous messages:
1)Try changing the modem port.
2)Try changing the POTS line.
3)The chassis needs to be properly grounded.
Thanks, Mak.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide