Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

3640 NM-2FE2W Problem,please help

Dear Sirs:

A new 3640 router with a NM-2FE2w and a NM-16AM, IOS Cisco Version 12.0(13), can not find the NM-2FE2W in show run, what can I do next? Thank you.

Some Information followed:

Router#show version

Cisco Internetwork Operating System Software

IOS (tm) 3600 Software (C3640-I-M), Version 12.0(13), RELEASE SOFTWARE (fc1)

Copyright (c) 1986-2000 by cisco Systems, Inc.

Compiled Tue 05-Sep-00 22:55 by linda

Image text-base: 0x60008918, data-base: 0x60684000

ROM: System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (f

c1)

Router uptime is 5 minutes

System restarted by power-on

System image file is "flash:c3640-i-mz.120-13"

cisco 3640 (R4700) processor (revision 0x00) with 24576K/8192K bytes of memory.

Processor board ID 26878039

R4700 processor, Implementation 33, Revision 1.0

Bridging software.

X.25 software, Version 3.0.0.

DRAM configuration is 64 bits wide with parity disabled.

125K bytes of non-volatile configuration memory.

8192K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

C3600 processor with 32768 Kbytes of main memory

Main memory is configured to 64 bit mode with parity disabled

program load complete, entry point: 0x80008000, size: 0x39074c

Self decompressing the image : #################################################

################################################################################

################################################################################

################################################################################

# [OK]

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.

170 West Tasman Drive

San Jose, California 95134-1706

Cisco Internetwork Operating System Software

IOS (tm) 3600 Software (C3640-I-M), Version 12.0(13), RELEASE SOFTWARE (fc1)

Copyright (c) 1986-2000 by cisco Systems, Inc.

Compiled Tue 05-Sep-00 22:55 by linda

Image text-base: 0x60008918, data-base: 0x60684000

cisco 3640 (R4700) processor (revision 0x00) with 24576K/8192K bytes of memory.

Processor board ID 26878039

R4700 processor, Implementation 33, Revision 1.0

Bridging software.

X.25 software, Version 3.0.0.

DRAM configuration is 64 bits wide with parity disabled.

125K bytes of non-volatile configuration memory.

8192K bytes of processor board System flash (Read/Write)

Press RETURN to get started!

00:00:03: %PA-2-UNDEFPA: Undefined Port Adaptor type 216 in bay 0

00:00:03: %LINK-4-NOMAC: A random default MAC address of 0000.0c83.8039 has

been chosen. Ensure that this address is unique, or specify MAC

addresses for commands (such as 'novell routing') that allow the

use of this address as a default.

00:00:05: %SYS-5-RESTART: System restarted --

Cisco Internetwork Operating System Software

IOS (tm) 3600 Software (C3640-I-M), Version 12.0(13), RELEASE SOFTWARE (fc1)

Copyright (c) 1986-2000 by cisco Systems, Inc.

Compiled Tue 05-Sep-00 22:55 by linda

Router>

Router>

Router>

5 REPLIES

Re: 3640 NM-2FE2W Problem,please help

hi

the minimum supported ios for the nm-2fe2w is 12.1 so you will need to upgrade your router, also more memory is needed i think. if you go to the TAC part of cisco's website there is a memory calculator on it use this and it will also tell you what ios and memory requirements you will need.

hope this helps

New Member

Re: 3640 NM-2FE2W Problem,please help

Thank you very much. Thanks Thanks Thanks

New Member

Re: 3640 NM-2FE2W Problem,please help

Hi,

I am looking for in my documentation and I think that this modules

( NM-2FE2w ) in not suported for the cisco 3640.

It is suported for 3620 or Serie 2600.

The other module is suported in 3640.

Sorry

Bye

Re: 3640 NM-2FE2W Problem,please help

this module is supported, you can check on the cisco web site but it is supported

New Member

Re: 3640 NM-2FE2W Problem,please help

Sorry, It 's true, My documentation is old

Sorry ;-)

225
Views
0
Helpful
5
Replies