08-07-2002 04:35 AM - edited 03-02-2019 12:29 AM
I have a 3640 with a 2 port FE card and a 1port FE card(NM-1FE-TX). Each port is connected as a trunk (ISL) to three seperate 3548 switches. No errors on the 2port card but errors on the single port card and on the switch port on the switch which terminates the trunk. Changed interface and switch and cable same errors.
Any ideas as to cause?
The errors are drop packets in the router and CRC errors in the switch:
Keith.
errors shown here:
ROUTER
show int fa1/0 sum
*: interface is up
IHQ: pkts in input hold queue IQD: pkts dropped from input queue
OHQ: pkts in output hold queue OQD: pkts dropped from output queue
RXBS: rx rate (bits/sec) RXPS: rx rate (pkts/sec)
TXBS: tx rate (bits/sec) TXPS: tx rate (pkts/sec)
TRTL: throttle count
Interface IHQ IQD OHQ OQD RXBS RXPS TXBS TXPS TRTL
----------------------------------------------------------------------
* FastEthernet1/0 0 696492 0 0 3000 6 2000 3 0
NOTE:No separate counters are maintained for subinterfaces
Hence Details of subinterface are not shown
NAPRT1#show int fa0/0 sum
*: interface is up
IHQ: pkts in input hold queue IQD: pkts dropped from input queue
OHQ: pkts in output hold queue OQD: pkts dropped from output queue
RXBS: rx rate (bits/sec) RXPS: rx rate (pkts/sec)
TXBS: tx rate (bits/sec) TXPS: tx rate (pkts/sec)
TRTL: throttle count
Interface IHQ IQD OHQ OQD RXBS RXPS TXBS TXPS TRTL
----------------------------------------------------------------------
* FastEthernet0/0 0 0 0 0 4000 7 3000 4 0
NOTE:No separate counters are maintained for subinterfaces
Hence Details of subinterface are not shown
NAPRT1#show int fa0/1 sum
*: interface is up
IHQ: pkts in input hold queue IQD: pkts dropped from input queue
OHQ: pkts in output hold queue OQD: pkts dropped from output queue
RXBS: rx rate (bits/sec) RXPS: rx rate (pkts/sec)
TXBS: tx rate (bits/sec) TXPS: tx rate (pkts/sec)
TRTL: throttle count
Interface IHQ IQD OHQ OQD RXBS RXPS TXBS TXPS TRTL
----------------------------------------------------------------------
* FastEthernet0/1 0 168 0 0 7000 14 14000 10 0
NOTE:No separate counters are maintained for subinterfaces
Hence Details of subinterface are not shown
RT1#show int fa1/0
FastEthernet1/0 is up, line protocol is up
Hardware is AmdFE, address is 0008.2190.58d0 (bia 0008.2190.58d0)
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s, 100BaseTX/FX
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/696492/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue :0/40 (size/max)
5 minute input rate 3000 bits/sec, 5 packets/sec
5 minute output rate 2000 bits/sec, 2 packets/sec
2560629 packets input, 150821824 bytes
Received 57039 broadcasts, 0 runts, 0 giants, 0 throttles
355951 input errors, 0 CRC, 0 frame, 355951 overrun, 0 ignored
0 watchdog
0 input packets with dribble condition detected
4882013 packets output, 2967272779 bytes, 0 underruns
0 output errors, 0 collisions, 10 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
SWITCH
how int fa0/48 sw
Name: Fa0/48
Switchport: Enabled
Administrative mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: isl
Operational Trunking Encapsulation: isl
Negotiation of Trunking: Disabled
Access Mode VLAN: 0 ((Inactive))
Trunking Native Mode VLAN: 1 (default)
Trunking VLANs Enabled: ALL
Trunking VLANs Active: 1-7
Pruning VLANs Enabled: 2-1001
Priority for untagged frames: 0
Override vlan tag priority: FALSE
Voice VLAN: none
Appliance trust: none
switch1A#show int fa0/48
FastEthernet0/48 is up, line protocol is up
Hardware is Fast Ethernet, address is 0009.7c48.0870 (bia 0009.7c48.0870)
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 254/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not set
Auto-duplex (Full), Auto Speed (100), 100BaseTX/FX
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:48, output 00:00:00, output hang never
Last clearing of "show interface" counters 03:23:53
Queueing strategy: fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 3000 bits/sec, 3 packets/sec
5 minute output rate 5000 bits/sec, 7 packets/sec
4881315 packets input, 2840592245 bytes
Received 4892 broadcasts, 0 runts, 0 giants, 0 throttles
1156 input errors, 1156 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 193 multicast
0 input packets with dribble condition detected
4647387 packets output, 309160702 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
08-13-2002 09:40 PM
Often times complex troubleshooting issues are best addressed in an interactive session with one of our trained technical assistance engineers. While other forum users may be able to help, its often difficult to do so for this type of issue.
To utilize the resources at our Technical Assistance Center, please visit http://www.cisco.com/tac and to open a case with one of our TAC engineers, visit http://www.cisco.com/tac/caseopen
If anyone else in the forum has some advice, please reply to this thread.
Thank you for posting.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide