Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

3825 Doesn't boot

I'm receiving this on a 3825:

program load complete, entry point: 0x8000f000, size: 0xc0c0

Initializing ATA monitor library.......

program load complete, entry point: 0x8000f000, size: 0xc0c0

Initializing ATA monitor library.......

loadprog: error - on read during ELF program load

requested 27157520 (0x19e6410) bytes, got 16748852 (0xff9134)

open: failed to find and/or load the bootloader: "flash:c3825-spservicesk9-mz.123-11.T8.bin"

loadprog: error - on file open

boot: cannot load "c3825-spservicesk9-mz.123-11.T8.bin"

System Bootstrap, Version 12.3(11r)T1, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 2004 by cisco Systems, Inc.

System Bootstrap, Version 12.3(11r)T2, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 2005 by cisco Systems, Inc.

Total memory size = 256 MB - DIMM0 = 256 MB, DIMM1 = 0 MB

c3825 processor with 262144 Kbytes of main memory

Main memory is configured to 72/0(dimm 0/1) bit mode with ECC enabled

Upgrade ROMMON initialized

program load complete, entry point: 0x8000f000, size: 0xc0c0

Initializing ATA monitor library.......

program load complete, entry point: 0x8000f000, size: 0xc0c0

Initializing ATA monitor library.......

loadprog: error - on read during ELF program load

requested 27157520 (0x19e6410) bytes, got 16748852 (0xff9134)

boot: cannot load "flash:"

System Bootstrap, Version 12.3(11r)T1, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 2004 by cisco Systems, Inc.

System Bootstrap, Version 12.3(11r)T2, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 2005 by cisco Systems, Inc.

Total memory size = 256 MB - DIMM0 = 256 MB, DIMM1 = 0 MB

c3825 processor with 262144 Kbytes of main memory

Main memory is configured to 72/0(dimm 0/1) bit mode with ECC enabled

Upgrade ROMMON initialized

program load complete, entry point: 0x8000f000, size: 0xc0c0

Initializing ATA monitor library.......

program load complete, entry point: 0x8000f000, size: 0xc0c0

Initializing ATA monitor library.......

loadprog: error - on read during ELF program load

requested 27157520 (0x19e6410) bytes, got 16748852 (0xff9134)

boot: cannot load "flash:"

System Bootstrap, Version 12.3(11r)T1, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 2004 by cisco Systems, Inc.

System Bootstrap, Version 12.3(11r)T2, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 2005 by cisco Systems, Inc.

Total memory size = 256 MB - DIMM0 = 256 MB, DIMM1 = 0 MB

c3825 processor with 262144 Kbytes of main memory

Main memory is configured to 72/0(dimm 0/1) bit mode with ECC enabled

Upgrade ROMMON initialized

rommon 1 >

2 REPLIES

Re: 3825 Doesn't boot

Appears, the IOS image is corrupted.

Follow the link below to load a valid image.

http://www.cisco.com/en/US/products/ps5854/prod_configuration_guide09186a00802c35e9.html#wp1051098

Good Luck!!

HTH,

Sundar

Re: 3825 Doesn't boot

You should be able to use the CF slot on 3825 , copy an image into the CF card and boot from it from rommon.

874
Views
0
Helpful
2
Replies