Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

4006: 802.1x support?

EOL has been announced for Cat 4006. Is anyone out there using 802.1x on these switches. If yes, could you please let me know what is the IOS.

The cisco feature selection tool (http://tools.cisco.com/ITDIT/CFN/jsp/index.jsp) says 8.4(11)GLX is available on CAT4000 with 802.1x. Not sure if it's the same.

Thanks

Ravi

1 ACCEPTED SOLUTION

Accepted Solutions

Re: 4006: 802.1x support?

The 4006 can have either sup 1 or sup 2 which are no longer being sold, these run CatOS. 4006 Chassis can alos support Supervisor Engine III (WS-X4014), and Supervisor Engine IV (WS-X4515) which runs IOS. 802.1x feature was first supported in version 6.2 for CatOS and since 12.1(19)EW on IOS.

CatOS Release Notes:

http://www.cisco.com/univercd/cc/td/doc/product/lan/cat4000/relnotes/ol_2117.htm

CAt IOS Release Notes:

http://www.cisco.com/univercd/cc/td/doc/product/lan/cat4000/relnotes/ol_2170.htm

So, I hope this answers your questions:

Is anyone out there using 802.1x on these switches. If yes, could you please let me know what is the IOS.

A: Sup1 and Sup2 for Ca4000 can only run CatOS. 802.1x had been supported since 6.2. Sup2+, Sup3 and Sup4 runs IOS and 802.1x had been supported since 12.1(19)

The cisco feature selection tool (http://tools.cisco.com/ITDIT/CFN/jsp/index.jsp) says 8.4(11)GLX is available on CAT4000 with 802.1x. Not sure if it's the same.

A: 802.1x is 802.1x for CatOS or Cat IOS just the CLI will change so one and the same

Please rate all posts.

2 REPLIES

Re: 4006: 802.1x support?

The 4006 can have either sup 1 or sup 2 which are no longer being sold, these run CatOS. 4006 Chassis can alos support Supervisor Engine III (WS-X4014), and Supervisor Engine IV (WS-X4515) which runs IOS. 802.1x feature was first supported in version 6.2 for CatOS and since 12.1(19)EW on IOS.

CatOS Release Notes:

http://www.cisco.com/univercd/cc/td/doc/product/lan/cat4000/relnotes/ol_2117.htm

CAt IOS Release Notes:

http://www.cisco.com/univercd/cc/td/doc/product/lan/cat4000/relnotes/ol_2170.htm

So, I hope this answers your questions:

Is anyone out there using 802.1x on these switches. If yes, could you please let me know what is the IOS.

A: Sup1 and Sup2 for Ca4000 can only run CatOS. 802.1x had been supported since 6.2. Sup2+, Sup3 and Sup4 runs IOS and 802.1x had been supported since 12.1(19)

The cisco feature selection tool (http://tools.cisco.com/ITDIT/CFN/jsp/index.jsp) says 8.4(11)GLX is available on CAT4000 with 802.1x. Not sure if it's the same.

A: 802.1x is 802.1x for CatOS or Cat IOS just the CLI will change so one and the same

Please rate all posts.

New Member

Re: 4006: 802.1x support?

bosalaza: would you happen to know if any CatOS on these switches support NAC?

Thanks

Ravi

240
Views
0
Helpful
2
Replies
CreatePlease to create content