06-23-2006 12:55 PM - edited 03-03-2019 03:47 AM
EOL has been announced for Cat 4006. Is anyone out there using 802.1x on these switches. If yes, could you please let me know what is the IOS.
The cisco feature selection tool (http://tools.cisco.com/ITDIT/CFN/jsp/index.jsp) says 8.4(11)GLX is available on CAT4000 with 802.1x. Not sure if it's the same.
Thanks
Ravi
Solved! Go to Solution.
06-23-2006 03:45 PM
The 4006 can have either sup 1 or sup 2 which are no longer being sold, these run CatOS. 4006 Chassis can alos support Supervisor Engine III (WS-X4014), and Supervisor Engine IV (WS-X4515) which runs IOS. 802.1x feature was first supported in version 6.2 for CatOS and since 12.1(19)EW on IOS.
CatOS Release Notes:
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat4000/relnotes/ol_2117.htm
CAt IOS Release Notes:
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat4000/relnotes/ol_2170.htm
So, I hope this answers your questions:
Is anyone out there using 802.1x on these switches. If yes, could you please let me know what is the IOS.
A: Sup1 and Sup2 for Ca4000 can only run CatOS. 802.1x had been supported since 6.2. Sup2+, Sup3 and Sup4 runs IOS and 802.1x had been supported since 12.1(19)
The cisco feature selection tool (http://tools.cisco.com/ITDIT/CFN/jsp/index.jsp) says 8.4(11)GLX is available on CAT4000 with 802.1x. Not sure if it's the same.
A: 802.1x is 802.1x for CatOS or Cat IOS just the CLI will change so one and the same
Please rate all posts.
06-23-2006 03:45 PM
The 4006 can have either sup 1 or sup 2 which are no longer being sold, these run CatOS. 4006 Chassis can alos support Supervisor Engine III (WS-X4014), and Supervisor Engine IV (WS-X4515) which runs IOS. 802.1x feature was first supported in version 6.2 for CatOS and since 12.1(19)EW on IOS.
CatOS Release Notes:
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat4000/relnotes/ol_2117.htm
CAt IOS Release Notes:
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat4000/relnotes/ol_2170.htm
So, I hope this answers your questions:
Is anyone out there using 802.1x on these switches. If yes, could you please let me know what is the IOS.
A: Sup1 and Sup2 for Ca4000 can only run CatOS. 802.1x had been supported since 6.2. Sup2+, Sup3 and Sup4 runs IOS and 802.1x had been supported since 12.1(19)
The cisco feature selection tool (http://tools.cisco.com/ITDIT/CFN/jsp/index.jsp) says 8.4(11)GLX is available on CAT4000 with 802.1x. Not sure if it's the same.
A: 802.1x is 802.1x for CatOS or Cat IOS just the CLI will change so one and the same
Please rate all posts.
06-26-2006 11:26 AM
bosalaza: would you happen to know if any CatOS on these switches support NAC?
Thanks
Ravi
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: