Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

4014 crashed and report Fatal K2 Error FFE 800040 PPE 0

A Catalyst 4006 with 4014 supervisor engine crashed and output the following:

Power-on-self-test for Module 1: WS-X4014

Port/Test Status: (. = Pass, F = Fail)

Port Traffic: L2 Serdes Loopback ...

0: . 1: . 2: . 3: . 4: . 5: . 6: . 7: . 8: . 9: . 10: . 11: .

12: . 13: . 14: . 15: . 16: . 17: . 18: . 19: . 20: . 21: . 22: . 23: .

24: . 25: . 26: . 27: . 28: . 29: . 30: . 31: .

Port Traffic: L2 Asic Loopback ...

0: . 1: . 2: . 3: . 4: . 5: . 6: . 7: . 8: . 9: . 10: . 11: .

12: . 13: . 14: . 15: . 16: . 17: . 18: . 19: . 20: . 21: . 22: . 23: .

24: . 25: . 26: . 27: . 28: . 29: . 30: . 31: .

Port Traffic: L3 Asic Loopback ...

0: . 1: . 2: . 3: . 4: . 5: . 6: . 7: . 8: . 9: . 10: . 11: .

12: . 13: . 14: . 15: . 16: . 17: . 18: . 19: . 20: . 21: . 22: . 23: .

24: . 25: . 26: . 27: . 28: . 29: . 30: . 31: . au: .

Switch Subsystem Memory ...

1: . 2: . 3: . 4: . 5: . 6: . 7: . 8: . 9: . 10: . 11: . 12: .

13: . 14: . 15: . 16: . 17: . 18: . 19: . 20: . 21: . 22: . 23: . 24: .

25: . 26: . 27: . 28: . 29: . 30: . 31: . 32: . 33: . 34: . 35: . 36: .

37: . 38: . 39: . 40: . 41: . 42: . 43: . 44: . 45: . 46: . 47: . 48: .

49: . 50: . 51: . 52: . 53: . 54: .

Module 1 Passed

Exiting to ios...

Rommon reg: 0x37000180

Running IOS...

Decompressing the image

################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################### [OK]

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.

170 West Tasman Drive

San Jose, California 95134-1706

Cisco Internetwork Operating System Software

IOS (tm) Catalyst 4000 L3 Switch Software (cat4000-I5S-M), Version 12.1(19)EW, EARLY DEPLOYMENT RELEASE SOFTWARE (fc2)

TAC Support: http://www.cisco.com/tac

Copyright (c) 1986-2003 by cisco Systems, Inc.

Compiled Fri 27-Jun-03 14:34 by kellythw

Image text-base: 0x00000000, data-base: 0x00F12C5C

Fatal K2 Error FFE 800040 PPE 0

**********************************************************

* *

* Welcome to Rom Monitor for WS-X4014 System. *

* Copyright (c) 2002 by Cisco Systems, Inc. *

* All rights reserved. *

* *

**********************************************************

Rom Monitor Program Version 12.1(12r)EW

Board type 1, Board revision 7

Swamp FPGA revision 16, Dagobah FPGA revision 55

MAC Address : 00-0b-be-04-5b-fe

Ip Address : Not set.

Netmask : Not set.

Gateway : Not set.

TftpServer : Not set.

Main Memory : 256 MBytes

***** The system will autoboot in 5 seconds *****

Type control-C to prevent autobooting.

. . . . .

Autoboot cancelled......... please wait!!!

rommon 1 > [interrupt]

rommon 1 > [interrupt]

rommon 1 >?

alias set and display aliases command

boot boot up an external process

clear clear configurations, use 'clear help' for more info

confreg configuration register utility

dev list the device table with physical device information

dir list filesystem information

dis disassemble instruction stream

help monitor builtin command help

history monitor command history

leds toggle traffic leds

macstats print management port MAC statistics counters

meminfo main memory information

ping ping utility to determine network connectivity

repeat repeat a monitor command

reset system reset

set show/set environment vars, use 'set help' for more info

sprom serial eprom operations

sysret print out info from last system return

unalias unset an alias

unset unset a monitor variable

version display Rom Monitor version information

rommon 2 >

136
Views
0
Helpful
0
Replies
CreatePlease to create content