Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

4507 Switch's Power Supply

Does the output indicate the "Bad Power Supply" or it is a configuration issue. This is a brand new switch.

----------------------------------------------------------------------------------------------------

Switch#show environment status powersupply

Power Fan Inline

Supply Model No Type Status Sensor Status

------ ---------------- --------- ----------- ------- -------

PS1 Unknown Type Unknown bad/off bad/off n.a.

PS2 none -- -- -- --

-----------------------------------------------------------------------------------------------------

Switch#show module all

Chassis Type : WS-C4507R

Power consumed by backplane : 40 Watts

Mod Ports Card Type Model Serial No.

---+-----+--------------------------------------+------------------+-----------

1 2 1000BaseX (GBIC) Supervisor(active) WS-X4013+ JAE0926FCYS

3 0 Not enough power for module WS-X4548-GB-RJ45V JAE0922E1T9

4 0 Not enough power for module WS-X4548-GB-RJ45V JAE0922E22N

5 0 Not enough power for module WS-X4424-GB-RJ45 JAE0917AGXF

M MAC addresses Hw Fw Sw Status

--+--------------------------------+---+------------+----------------+---------

1 0014.a8d6.a200 to 0014.a8d6.a201 3.3 12.2(20r)EW1 12.2(18)EW3 Ok

3 0014.69ae.96e0 to 0014.69ae.970f 2.2 Pwr Deny

4 0014.69ae.9770 to 0014.69ae.979f 2.2 Pwr Deny

5 0012.7fc6.3478 to 0012.7fc6.348f 1.7 Pwr Deny

----------------------------------------------------------------------------------------------------------------------------------

Switch#show power

Power Fan Inline

Supply Model No Type Status Sensor Status

------ ---------------- --------- ----------- ------- -------

PS1 Unknown Type Unknown bad/off bad/off n.a.

PS2 none -- -- -- --

Power supplies needed by system : 1

Power supplies currently available : 0

*** Insufficient power supplies present for specified configuration ***

Power Summary Maximum

(in Watts) Used Available

---------------------- ---- ---------

System Power (12V) 250 0

Inline Power (-50V) 0 0

Backplane Power (3.3V) 40 0

---------------------- ----

Total Used 290 (not to exceed Total Maximum Available = 0)

*** Insufficient power available for current chassis configuration! ***

Switch#show ver

Cisco Internetwork Operating System Software

IOS (tm) Catalyst 4000 L3 Switch Software (cat4000-I9S-M), Version 12.2(18)EW3, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2005 by cisco Systems, Inc.

Compiled Mon 07-Feb-05 19:21 by hqluong

Image text-base: 0x00000000, data-base: 0x010BFA78

ROM: 12.2(20r)EW1

Dagobah Revision 95, Swamp Revision 3

Switch uptime is 2 minutes

System returned to ROM by reload

System image file is "bootflash:"

cisco WS-C4507R (MPC8245) processor (revision 4) with 262144K bytes of memory.

Processor board ID FOX092206E6

Last reset from Reload

1 Virtual Ethernet/IEEE 802.3 interface(s)

2 Gigabit Ethernet/IEEE 802.3 interface(s)

511K bytes of non-volatile configuration memory.

Configuration register is 0x2101

Switch#

1 REPLY

Re: 4507 Switch's Power Supply

What p/sis it ? have you tried switching power supply to another slot ? Do you have the part number for the p/s

454
Views
0
Helpful
1
Replies
CreatePlease login to create content