cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
331
Views
0
Helpful
4
Replies

6509 sh ver out put contains error message

kmccann
Level 1
Level 1

Hi,

Can anyone help me out with a 6509 error message?

'sh ver' output (below) contains the message:-

'EXTBAN checksum failed'

Does anyone know what this means? Switch does not seem to suffer any adverse effects.

Thanks in advance

Keith

ouput follow:-

sh ver

WS-C6509 Software, Version NmpSW: 6.3(3)

Copyright (c) 1995-2001 by Cisco Systems

NMP S/W compiled on Oct 29 2001, 15:42:29

System Bootstrap Version: 6.1(4)

System Web Interface Version: Engine Version: 5.3 ADP Device: Cat6000 ADP Versi0

Hardware Version: 3.0 Model: WS-C6509 Serial #: TBA05430269

PS1 Module: WS-CAC-1300W Serial #: SNI05401059

PS2 Module: WS-CAC-1300W Serial #: SNI05401067

Mod Port Model Serial # Versions

--- ---- ------------------- ----------- --------------------------------------

1 2 WS-X6K-SUP2-2GE SAD054204FS Hw : 3.2

Fw : 6.1(4)

Fw1: 6.1(3)

Sw : 6.3(3)

Sw1: 6.3(3)

WS-F6K-PFC2 SAD054200KF Hw : 2.0

2 2 WS-X6K-SUP2-2GE SAD054205T8 Hw : 3.2

Fw : 6.1(4)

Fw1: 6.1(3)

Sw : 6.3(3)

Sw1: 6.3(3)

WS-F6K-PFC2 SAD054302UE Hw : 2.0

3 16 WS-X6416-GBIC SAL0543DQE4 Hw : 1.0

Fw : 5.4(2)

Sw : 6.3(3)

4 48 WS-X6348-RJ-45 SAL0544E2H1 Hw : 5.0

Fw : 5.4(2)

Sw : 6.3(3)

15 1 WS-F6K-MSFC2 SAD054106ER Hw : 1.2

Fw : 12.1(8a)E5

Sw : 12.1(8a)E5

16 1 WS-F6K-MSFC2 SAD054300C5 Hw : 1.2

Fw : 12.1(8a)E5

Sw : 12.1(8a)E5

DRAM FLASH NVRAM

Module Total Used Free Total Used Free Total Used Free

------ ------- ------- ------- ------- ------- ------- ----- ----- -----

1 130944K 66350K 64594K 32768K 10371K 22397K 512K 277K 235K

EXTBAN checksum failed.

Uptime is 353 days, 18 hours, 14 minutes

4 Replies 4

Prashanth Krishnappa
Cisco Employee
Cisco Employee

Take a look at the following bug CSCdx87646

http://www.cisco.com/cgi-bin/bugtool/onebug.pl?bugid=CSCdx87646

efrahim
Level 4
Level 4

This means you will lose the part of the config when the switch reloads due to some corruption. So please save the config and reload the switch.

This bug has been fixed in 7-5-1, 6-3-11 etc

esp config related to something with the banners in your config might be lost

Hi,

Thanks for the advice. I'm not certain the bug matches exactly. We don't have the red light and 'sh test 1' does is not shows NVRAM passed. However, I think we will save the config and reload the switch and I'll let you know the outcome

Thanks for all the help

Best regards

Keith

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: