Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Attention: The Community will be in read-only mode on 12/14/2017 from 12:00 am pacific to 11:30 am.

During this time you will only be able to see content. Other interactions such as posting, replying to questions, or marking content as helpful will be disabled for few hours.

We apologize for the inconvenience while we perform important updates to the Community.

New Member

7513 active ISDN calls SNMP object ID

I need to poll a 7513 with 4 PRI cards and get the total number of active ISDN calls. I've loaded the POP and ISDN MIBS and browsed both, the POP MIB doesn't return any counters whatsoever. The ISDN MIB lists everything I could ever want to know but not the total number of calls on the router/PRI card. I'm using MRTG so I need just to retrive a single value rather than doing any form of calculation.

My only thought is that I may be able to get the figure from the PRI interface card but I don't know what the OID/MIB would be for that, any suggestions?

2 REPLIES
Blue

Re: 7513 active ISDN calls SNMP object ID

For POP-MGMT-MIB not returning any values, you first need to verify whether the IOS image that you're using have this MIB present in it or not. If the MIB is not present, you will not see any results in the output. You can use CCO MIB Locator Tool for this purpose (http://www.cisco.com/go/mibs). For the ISDN-MIB, if it's not giving the total number of calls on the PRI, it simply means that the MIB object for this particular thing is not available in this MIB.

New Member

Re: 7513 active ISDN calls SNMP object ID

I've got the same problem with 3620 and 8 port BRI ISDN card. I asked this at remote access group:

----------o<------------

Hi,

i have one Cisco3620 router with one 8 ISDN Basic Rate interface, and version 12.2(6) IOS. The router is properly configured for ISDN dial-in users, and i want to monitor the active calls with MRTG, or RRDTools via SNMP queries.

I red about interested CISCO-POP-MGMP-MIB entries from Cisco's Dial NMS implementation guide, and when try to use these, the answer is:

$snmpwalk 10.1.0.1 drvread .1.3.6.1.4.1.9.10.19

enterprises.9.10.19.1.1.2.0 = Gauge32: 0

enterprises.9.10.19.1.1.3.0 = Gauge32: 0

enterprises.9.10.19.1.1.4.0 = Gauge32: 0

enterprises.9.10.19.1.1.5.0 = Gauge32: 0

enterprises.9.10.19.1.1.6.0 = Gauge32: 0

enterprises.9.10.19.1.1.7.0 = Gauge32: 0

enterprises.9.10.19.1.1.8.0 = Counter32: 0

enterprises.9.10.19.1.1.10.0 = Gauge32: 0

enterprises.9.10.19.1.1.11.0 = Gauge32: 0

enterprises.9.10.19.1.1.12.0 = Gauge32: 0

enterprises.9.10.19.1.2.1.0 = Counter32: 0

enterprises.9.10.19.1.2.2.0 = Counter32: 0

enterprises.9.10.19.1.2.3.0 = Counter32: 0

enterprises.9.10.19.1.2.4.0 = Counter32: 0

enterprises.9.10.19.1.2.5.0 = Counter32: 0

enterprises.9.10.19.1.2.6.0 = Counter32: 0

enterprises.9.10.19.1.4.1.0 = 100

enterprises.9.10.19.1.4.2.0 = 15

enterprises.9.10.19.1.5.1.0 = 2

enterprises.9.10.19.1.6.1.0 = 2

Can I somehow monitor the active call's with SNMP from 3620, or this works only with 5xxx ASs? Why doesn't work the mentioned MIB?

Best regards,

Qrta

----------o<------------

and the answare was:

----------o<------------

mljohnson - CISCO SYSTEMS, CCIE

Oct 24, 2002, 11:22am PST

Yes, this should be supported by the 3620:

http://www.cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtml

MRTG should not be a problem, either:

http://www.cisco.com/univercd/cc/td/doc/cisintwk/intsolns/dialsol/nmssol/mrtg.htm

You may want to try the Network Management group for more help.

----------o<------------

So, works the MIB, or not?

Best regards,

Qrta

319
Views
0
Helpful
2
Replies
CreatePlease to create content