Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

After 7513Router(RSP2-->RSP8), RSP-3-error, FEIP2-1-MSG....

hi.

After RSP2--> RSP8, so many error message and reboot..

We are getting so many error message on 7513 router.

what can be the solution for this.

7513Router# sh ver

Cisco Internetwork Operating System Software

IOS (tm) RSP Software (RSP-JSV-M), Version 12.2(2)T1, RELEASE SOFTWARE (fc2)

TAC Support: http://www.cisco.com/tac

Copyright (c) 1986-2001 by cisco Systems, Inc.

Compiled Wed 18-Jul-01 08:00 by ccai

Image text-base: 0x600109C8, data-base: 0x61A88000

ROM: System Bootstrap, Version 12.0(10r)S1, RELEASE SOFTWARE (fc1)

7513router uptime is 3 days, 20 hours, 2 minutes

System returned to ROM by processor memory parity error at PC 0x60DC3448, address 0x0

at 23:14:42 KST Mon Mar 24 2003

System image file is "slot0:rsp-jsv-mz.122-2.T1.bin"

cisco RSP8 (R7000) processor with 131072K/8216K bytes of memory.

R7000 CPU at 250Mhz, Implementation 39, Rev 2.1, 256KB L2, 2048KB L3 Cache

Last reset from power-on

G.703/E1 software, Version 1.0.

G.703/JT2 software, Version 1.0.

X.25 software, Version 3.0.0.

SuperLAT software (copyright 1990 by Meridian Technology Corp).

Bridging software.

TN3270 Emulation software.

Chassis Interface.

1 FSIP controller (4 Serial).

1 GEIP controller (1 GigabitEthernet).

1 FEIP2 controller (2 FastEthernet).

1 VIP4-80 RM7000 controller (6 Serial).

2 FastEthernet/IEEE 802.3 interface(s)

1 Gigabit Ethernet/IEEE 802.3 interface(s)

10 Serial network interface(s)

2043K bytes of non-volatile configuration memory.

20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K).

16384K bytes of Flash internal SIMM (Sector size 256K).

No slave installed in slot 7.

Configuration register is 0x2102

7513Router# sh log

*Jul 1 23:06:22: %RSP-3-ERROR: MD error 0080000020000000

-Traceback= 6039A0F4 6039A810 6039A948 6039B38C 603650DC

*Jul 1 23:06:22: %RSP-3-ERROR: SRAM parity error (bytes 0:7) 08

-Traceback= 6039A1D0 6039A810 6039A948 6039B38C 603650DC

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 CYASIC Error Interrupt register 0xC

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 Parity Error internal to CYA

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 Parity Error in data from CyBus

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 CYASIC Other Interrupt register 0x100

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 QE HIGH Priority Interrupt

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 QE RX HIGH Priority Interrupt

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 CYBUS Error Cmd/Addr 0xD001A12

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 MPUIntfc/PacketBus Error register 0x0

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 PMA error register = 0080002808000000

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 Packet Bus Write Parity error

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 PCI master address = 0800028

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 PA Bay 0 Upstream PCI-PCI Bridge, Handle=0

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 DEC21050 bridge chip, config=0x0

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 (0x00):dev, vendor id = 0x00011011

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 (0x04):status, command = 0x02800147

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 (0x08):class code, revid = 0x06040002

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 (0x0C):hdr, lat timer, cls = 0x00010000

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 (0x18):sec lat,cls & bus no = 0x08010100

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 (0x1C):sec status, io base = 0x22807020

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 Received Master Abort on secondars

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 (0x20):mem base & limit = 0x01F00000

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 (0x24):prefetch membase/lim = 0x0000FE00

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 (0x3C):bridge ctrl = 0x00030000

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 (0x40):arb/serr, chip ctrl = 0x00100000

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 (0x44):pri/sec trgt wait t. = 0x00000000

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 (0x48):sec write attmp ctr = 0x00FFFFFF

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 (0x4C):pri write attmp ctr = 0x00FFFFFF

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 PA Bay 1 Upstream PCI-PCI Bridge, Handle=1

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 DEC21050 bridge chip, config=0x0

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 (0x00):dev, vendor id = 0x00011011

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 (0x04):status, command = 0x02800147

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 (0x08):class code, revid = 0x06040002

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 (0x0C):hdr, lat timer, cls = 0x00010000

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 (0x18):sec lat,cls & bus no = 0x08020200

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 (0x1C):sec status, io base = 0x2280F0A0

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 Received Master Abort on secondars

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 (0x20):mem base & limit = 0x03F00200

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 (0x24):prefetch membase/lim = 0x0000FE00

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 (0x3C):bridge ctrl = 0x00030000

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 (0x40):arb/serr, chip ctrl = 0x00100000

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 (0x44):pri/sec trgt wait t. = 0x00000000

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 (0x48):sec write attmp ctr = 0x00FFFFFF

*Jul 1 23:06:22: %FEIP2-1-MSG: slot8 (0x4C):pri write attmp ctr = 0x00FFFFFF

*Jul 1 23:06:23: %FEIP2-1-MSG: slot8 System reloaded by a fatal hardware error

*Jul 1 23:06:23: %FEIP2-1-MSG: slot8 caller=0x60104D3C

*Jul 1 23:06:23: %FEIP2-1-MSG: slot8 System exception: sig=22, code=0x0, context09425E8

*Jul 1 23:06:23: %FEIP2-1-MSG: slot8 $0 : 00000000, AT : E100003C, v0 : 300007E0 : 00000064,

*Jul 1 23:06:23: %FEIP2-1-MSG: slot8 a0 : 00000200, a1 : 00000001, a2 : 60910000 : 300404F0,

*Jul 1 23:06:23: %FEIP2-1-MSG: slot8 t0 : 30006A10, t1 : 00000000, t2 : 00000000 : 80000000,

*Jul 1 23:06:23: %FEIP2-1-MSG: slot8 t4 : 6093DA98, t5 : FFFFFFFF, t6 : C1000000 : 00000003,

*Jul 1 23:06:23: %FEIP2-1-MSG: slot8 s0 : 00000000, s1 : 00001E00, s2 : 80007DB8 : 0000000C,

*Jul 1 23:06:23: %FEIP2-1-MSG: slot8 s4 : 60900000, s5 : 0000000E, s6 : 608F0000 : 00000000,

*Jul 1 23:06:23: %FEIP2-1-MSG: slot8 t8 : 61069364, t9 : 00000000, k0 : 00000000 : 0000015A,

*Jul 1 23:06:23: %FEIP2-1-MSG: slot8 gp : 6084A140, sp : 6093DAD8, s8 : 00000000 : 60293B6C,

*Jul 1 23:06:23: %FEIP2-1-MSG: slot8 EPC : 60292658, ErrorEPC : 80008698, SREG :0E103

*Jul 1 23:06:23: %FEIP2-1-MSG: slot8 Cause 00001000 (Code 0x0)

*Jul 1 23:06:23: %FEIP2-1-MSG: slot8 Traceback= 60292658 60293B6C 60104C20

*Jul 1 23:06:25: %RSP-3-ERROR: End of MEMD error interrupt processing

-Traceback= 6039A8E0 6039A948 6039B38C 603650DC

*Jul 1 23:06:25: %DBUS-3-CXBUSERR: Slot 8, CBus Error

*Jul 1 23:06:25: %DBUS-3-DBUSINTERRSWSET: Slot 8, Internal Error due to VIP cras

*Jul 1 23:06:53: %SYS-3-CPUHOG: Task ran for 10512 msec (7/0), process = OIR Han, PC = 603E7520.

-Traceback= 603E7528 60338F8C 60338F78

*Jul 1 23:06:55: %LINK-3-UPDOWN: Interface FastEthernet8/0/0, changed state to down

*Jul 1 23:06:55: %LINK-3-UPDOWN: Interface FastEthernet8/1/0, changed state to down

*Jul 1 23:06:56: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet8/0 changed state to down

*Jul 1 23:06:56: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet8/1 changed state to down

*Jul 1 23:07:04: %LINK-3-UPDOWN: Interface FastEthernet8/0/0, changed state to up

*Jul 1 23:07:04: %LINK-3-UPDOWN: Interface FastEthernet8/1/0, changed state to up

*Jul 1 23:07:05: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet8/0 changed state to up

*Jul 1 23:07:06: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet8/1 changed state to up

*Jul 1 23:11:22: %FIB-3-FIBDISABLE: Fatal error, slot 8: No window message, LC to IPC is non-operational

3 REPLIES
Cisco Employee

Re: After 7513Router(RSP2-->RSP8), RSP-3-error, FEIP2-1-MSG....

Those messages do not sound very healthy. I would have the FEIP replaced.

Silver

Re: After 7513Router(RSP2-->RSP8), RSP-3-error, FEIP2-1-MSG....

check tihis page for tS Vips

http://www.cisco.com/warp/public/63/vip_crash.html

I would remove the VIP and reseat the DRAM , then reload the box, If this still occurs open a TAC case to have the VIP replaced .

Bronze

Re: After 7513Router(RSP2-->RSP8), RSP-3-error, FEIP2-1-MSG....

Hi,

If the RSP is the only (hardware) change that you made recently, chances are that it is that. Bad SRAM on the RSP can cause problems like this (including crashing the VIP). Does this always happen with the VIP in slot 8, or does it happen with different vips? (If it happens with multiple vips, or you get differnt crashed each time, you probably have a bad RSP) Can you move the vip in 8 to a different slot, and see if it starts happening with the new slot?

Good luck,

Warren.

98
Views
0
Helpful
3
Replies
CreatePlease login to create content