Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

AS5300 Modems don't PickUp

Hi, i have an AS5300, but the modems dont pick up the call, i think that is the AT commands, i try with it, but nothing, how i can do?? thanks..

modemcap entry my_mica:MSC=&F&D2S0=0S34=18000S40=10S10=50debugthismodemS71=4

modemcap entry v90:MSC=&f&d2s0=1s50=46000s30=31200s7=90s39=6

modemcap entry v92 &F&D2S54=16584S0=0S29=12S21=15S62=8S63=3S34=18000S40=10S10=50

modemcap entry v92:SPD=SPD:DTE=56000

2 REPLIES
Silver

Re: AS5300 Modems don't PickUp

Depending on the modem portware (sh modem version), please try the modemcaps as mentioned in the below URL:

http://cisco.com/en/US/tech/tk801/tk36/technologies_tech_note09186a008009491b.shtml

The following debugs will be useful for a call in:

deb modem/ deb modem csm / deb isdn q931 or deb cas (based on the PRI or CAS) line / deb ppp nego

Relevant part of the config will be good to see too, like under the controllers/ interface group-asyn x / under the lines.

Thanks, Mak.

New Member

Re: AS5300 Modems don't PickUp

sorry, the portware version is mica 2.9.5.0

the ios ver is: IOS (tm) 5300 Software (C5300-IS-M), Version 12.2(6b), RELEASE SOFTWARE (fc1)

this the config line running now

line 1 30

session-timeout 20

exec-timeout 0 20

password 7 ****

no flush-at-activation

modem Dialin

modem autoconfigure type my_mica

transport input all

autoselect during-login

autoselect ppp

the controller:

controller E1 0

framing NO-CRC4

clock source line primary

line-termination 75-ohm

ds0-group 0 timeslots 1-15,17-30 type r2-digital r2-compelled ani

cas-custom 0

country venezuela use-defaults

and group-async

interface Group-Async0

physical-layer async

description Pool E1 1-30

ip unnumbered Loopback0

ip nat inside

encapsulation ppp

no ip route-cache

no ip mroute-cache

async default routing

async mode interactive

no snmp trap link-status

peer default ip address pool MODEMUCLA

ppp max-bad-auth 3

ppp authentication pap chap

ppp timeout retry 1

no group-range

the debug appear this>

5d21h: Mica Modem(1/81): Rcvd Dial String()

5d21h: Mica Modem(1/81): Soft Reset

5d21h: Mica Modem(1/81): State Transition to Terminating

5d21h: Mica Modem(1/81): State Transition to Idle

5d21h: Mica Modem(1/119): Rcvd Dial String()

5d21h: Mica Modem(1/119): Soft Reset

5d21h: Mica Modem(1/119): State Transition to Terminating

5d21h: Mica Modem(1/119): State Transition to Idle

5d21h: Mica Modem(1/43): Rcvd Dial String()

5d21h: Mica Modem(1/43): Soft Reset

5d21h: Mica Modem(1/43): State Transition to Terminating

5d21h: Mica Modem(1/43): State Transition to Idle

thanks...

112
Views
0
Helpful
2
Replies
CreatePlease login to create content