Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Bonding Ts between 7206 and 2500

I need to bond 2 T1 circuits between a 7206 router on one end and a 2500 router on the other.

I have no problem defining the serial interfaces and bonding them together under a multilink-group ID - but I can't see how to do this on the 2500. Here is a sho ver for both end:

Cisco 7206

Cisco Internetwork Operating System Software

IOS (tm) 7200 Software (C7200-IS-M), Version 12.0(5)XE6, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

TAC:Home:SW:IOS:Specials for info

Copyright (c) 1986-1999 by cisco Systems, Inc.

Compiled Thu 30-Dec-99 10:22 by htseng

Image text-base: 0x60008900, data-base: 0x613AE000

ROM: System Bootstrap, Version 12.0(19990210:195103) [12.0XE 105], DEVELOPMENT SOFTWARE

BOOTFLASH: 7200 Software (C7200-BOOT-M), Version 12.0(2)XE2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

Ilitch7206 uptime is 1 hour, 1 minute

System returned to ROM by bus error at PC 0x0, address 0x0 at 10:04:32 eastern Mon Apr 5 2004

System restarted at 10:06:05 eastern Mon Apr 5 2004

System image file is "slot0:c7200-is-mz.120-5.XE6"

cisco 7206VXR (NPE300) processor with 122880K/40960K bytes of memory.

R7000 CPU at 262Mhz, Implementation 39, Rev 1.0, 256KB L2, 2048KB L3 Cache

6 slot VXR midplane, Version 2.0

Last reset from power-on

Bridging software.

X.25 software, Version 3.0.0.

Primary Rate ISDN software, Version 1.1.

2 FastEthernet/IEEE 802.3 interface(s)

8 Serial network interface(s)

8 Channelized T1/PRI port(s)

125K bytes of non-volatile configuration memory.

20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K).

4096K bytes of Flash internal SIMM (Sector size 256K).

Configuration register is 0x102

=======================================================================

Cisco 2500

Cisco Internetwork Operating System Software

IOS (tm) 2500 Software (C2500-D-L), Version 12.0(6), RELEASE SOFTWARE (fc1)

Copyright (c) 1986-1999 by cisco Systems, Inc.

Compiled Tue 10-Aug-99 23:52 by phanguye

Image text-base: 0x030382E0, data-base: 0x00001000

ROM: System Bootstrap, Version 5.2(8a), RELEASE SOFTWARE

BOOTFLASH: 3000 Bootstrap Software (IGS-RXBOOT), Version 10.2(8a), RELEASE SOFTWARE (fc1)

JLA_to_Fox uptime is 24 weeks, 6 days, 4 hours, 43 minutes

System restarted by power-on at 06:22:54 eastern Tue Oct 14 2003

System image file is "flash:c2500_i_j_m_12-1.bin"

cisco 2500 (68030) processor (revision E) with 16384K/2048K bytes of memory.

Processor board ID 02955553, with hardware revision 00000000

Bridging software.

X.25 software, Version 3.0.0.

1 Ethernet/IEEE 802.3 interface(s)

1 Token Ring/IEEE 802.5 interface(s)

2 Serial network interface(s)

32K bytes of non-volatile configuration memory.

8192K bytes of processor board System flash (Read ONLY)

Configuration register is 0x2102

============================================

I don't see a way to define Multilink on the 2500.

Am I way out of luck here??

Thanks.

1 REPLY
New Member

Re: Bonding Ts between 7206 and 2500

Multilink does work on the 2500's, I've done it before.

Where exactly is your problem:

A. Define your virtual interface (interface virtual-template)

B. Adding "ppp multilink" to your physical interfaces

Ron

149
Views
0
Helpful
1
Replies