10-15-2002 09:04 AM - edited 03-02-2019 02:05 AM
hi all
I've installed a new bootloader PA recognition issue, instruct my router to boot on it and it doesn't work
what did i forget?
note : the boot system cmde is ok,disk0 is supported
here are an extract of conf and error messages from boot sequence.
new-berg2(boot)#sh conf
Using 28397 out of 129016 bytes
!
! Last configuration change at 08:00:31 UTC Mon Oct 14 2002
! NVRAM config last updated at 08:00:37 UTC Mon Oct 14 2002
!
version 12.2
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname new-berg2
!
boot system disk0:c7200-js-mz.122-8.T5.bin
boot bootldr disk0:c7200-kboot-mz.122-8.T5.bin
no logging console
enable secret
--------------------------------------------------------------------------------------------
new-berg2#sh bootvar
BOOT variable = disk0:c7200-js-mz.122-8.T5.bin,12;
CONFIG_FILE variable does not exist
BOOTLDR variable = disk0:c7200-kboot-mz.122-8.T5.bin
Configuration register is 0x2102
------------------------------------------------------------------------------------------------------
new-berg2#
System Bootstrap, Version 12.2(4r)B, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2002 by cisco Systems, Inc.
C7200 platform with 262144 Kbytes of main memory
device does not contain a valid magic number
loadprog: error - on file open
open: failed to find and/or load the bootloader:
"disk0:c7200-kboot-mz.122-8.T5.bin"
loadprog: error - on file open
boot: cannot load "cisco2-C7200"
System Bootstrap, Version 12.2(4r)B, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2002 by cisco Systems, Inc.
C7200 platform with 262144 Kbytes of main memory
device does not contain a valid magic number
loadprog: error - on file open
boot: cannot load "disk0:c7200-js-mz.122-8.T5.bin"
System Bootstrap, Version 12.2(4r)B, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2002 by cisco Systems, Inc.
C7200 platform with 262144 Kbytes of main memory
device does not contain a valid magic number
boot: cannot open "disk0:"
boot: cannot determine first file name on device "disk0:"
System Bootstrap, Version 12.2(4r)B, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2002 by cisco Systems, Inc.
C7200 platform with 262144 Kbytes of main memory
Self decompressing the image :
############################################################################################################################################################################################################################################################################################################################################################################################################################
[OK]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) 7200 Software (C7200-KBOOT-M), Version 12.1(8a)E, EARLY
DEPLOYMENT RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2001 by cisco Systems, Inc.
Compiled Mon 09-Jul-01 06:20 by hqluong
Image text-base: 0x60008950, data-base: 0x6072A000
cisco 7206VXR (NPE400) processor (revision A) with 245760K/16384K bytes
of memory.
Processor board ID 26789518
R7000 CPU at 350Mhz, Implementation 39, Rev 3.3, 256KB L2, 4096KB L3
Cache
6 slot VXR midplane, Version 2.6
Last reset from power-on
Bridging software.
X.25 software, Version 3.0.0.
1 Ethernet/IEEE 802.3 interface(s)
1 Gigabit Ethernet/IEEE 802.3 interface(s)
4 Serial network interface(s)
125K bytes of non-volatile configuration memory.
46976K bytes of ATA PCMCIA card at slot 0 (Sector size 512 bytes).
46976K bytes of ATA PCMCIA card at slot 1 (Sector size 512 bytes).
8192K bytes of Flash internal SIMM (Sector size 256K).
Invalid device id
Thanks a lot
10-22-2002 07:58 AM
I only see a format error in this case. Reformat and try again
01-10-2003 11:42 AM
I am getting the same error, a reformat of the compact flash does not fix, any other ideas...?
01-10-2003 01:43 PM
Hi,
Did you test with boot system flash disk0:c7200-js-mz.122-8.T5.bin command ?
regards,
Carlos
01-10-2003 02:15 PM
Yes i did, it will only boot the boot helper image
01-14-2003 03:45 AM
Hi,
verify the config-reg, show version command, must be 0x2102 or 0x102.
regards,
Carlos
01-14-2003 04:52 AM
do a verify disk0:c7200-kboot-mz.122-8.T5.bin . I think the image may be corrupted.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide