Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

Bronze

C6006 Switch

hi,

i am looking forward to configure the cisco c6006 switch and its running catalyst

WS-C6006 Software, Version NmpSW: 5.5(1)

can anyone give me the guide as where to start from, any guides and documentation.

4 REPLIES

Re: C6006 Switch

NOt knowing what you want to do and what you want to configure, I can only give you the link on 5.5.x configuration guide:

http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/sw_5_5/cnfg_gd/index.htm

Please rate all posts.

Re: C6006 Switch

Could you send me the output of

sh ver

sh mod

then I can guess what are possible with your switch.

Bronze

Re: C6006 Switch

SH VER

-----------------------------------------------------

WS-C6006 Software, Version NmpSW: 5.5(1)

Copyright (c) 1995-2000 by Cisco Systems

NMP S/W compiled on Jun 8 2000, 21:09:45

System Bootstrap Version: 5.3(1)

Hardware Version: 2.0 Model: WS-C6006 Serial #: TBA04371184

Mod Port Model Serial # Versions

--- ---- ------------------- ----------- --------------------------------------

1 2 WS-X6K-SUP1A-2GE SAD043503FM Hw : 3.2

Fw : 5.3(1)

Fw1: 5.4(2)

Sw : 5.5(1)

Sw1: 5.5(1)

L2 Switching Engine SAD0437041L Hw : 2.0

2 2 WS-X6K-SUP1A-2GE SAD04290NH5 Hw : 3.2

Fw : 5.3(1)

Fw1: 5.4(2)

Sw : 5.5(1)

Sw1: 5.5(1)

L2 Switching Engine SAD0437043X Hw : 2.0

3 8 WS-X6408-GBIC SAD043506KG Hw : 2.6

Fw : 5.4(2)

Sw : 5.5(1)

4 48 WS-X6248-RJ-45 SAD041304LB Hw : 1.2

Fw : 5.1(1)CSX

Sw : 5.5(1)

DRAM FLASH NVRAM

Module Total Used Free Total Used Free Total Used Free

------ ------- ------- ------- ------- ------- ------- ----- ----- -----

1 65408K 31304K 34104K 16384K 6925K 9459K 512K 230K 282K

Uptime is 1671 days, 9 hours, 33 minutes

-----------------------------------------------------

SH MOD

-----------------------------------------------------

Mod Slot Ports Module-Type Model Sub Status

--- ---- ----- ------------------------- ------------------- --- --------

1 1 2 1000BaseX Supervisor WS-X6K-SUP1A-2GE yes ok

2 2 2 1000BaseX Supervisor WS-X6K-SUP1A-2GE yes standby

3 3 8 1000BaseX Ethernet WS-X6408-GBIC no ok

4 4 48 10/100BaseTX Ethernet WS-X6248-RJ-45 no ok

Mod Module-Name Serial-Num

--- ------------------- -----------

1 SAD043503FM

2 SAD04290NH5

3 SAD043506KG

4 SAD041304LB

Mod MAC-Address(es) Hw Fw Sw

--- -------------------------------------- ------ ---------- -----------------

1 00-d0-c0-d2-f9-52 to 00-d0-c0-d2-f9-53 3.2 5.3(1) 5.5(1)

00-d0-c0-d2-f9-50 to 00-d0-c0-d2-f9-51

00-03-a0-3a-e8-00 to 00-03-a0-3a-eb-ff

2 00-02-7e-24-40-36 to 00-02-7e-24-40-37 3.2 5.3(1) 5.5(1)

00-02-7e-24-40-34 to 00-02-7e-24-40-35

3 00-01-64-13-2b-d8 to 00-01-64-13-2b-df 2.6 5.4(2) 5.5(1)

4 00-01-97-10-d1-d0 to 00-01-97-10-d1-ff 1.2 5.1(1)CSX 5.5(1)

Mod Sub-Type Sub-Model Sub-Serial Sub-Hw

--- ----------------------- ------------------- ----------- ------

1 L2 Switching Engine II WS-F6020A SAD0437041L 2.0

2 L2 Switching Engine II WS-F6020A SAD0437043X 2.0

hope this helps

Re: C6006 Switch

Could you please tell me you want to use this catalyst 6506 as a Layer2 switch or layer3 switch.

please send me output of these commands, I wll help you to configure your needs.

If no output comes please indicate it.

show flash

show bootflash

show sup-bootfalsh

show slot0

show boot

show run

show config

I am still trying to identify weather this equipment has a native IOS image in its sup boot falsh.

Please note that you can use cat6506 as a layer2 switch, Layer3 switch(Hybid) and layer3 switch(Native).

Regards,

Ganganath

191
Views
0
Helpful
4
Replies
CreatePlease to create content