Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Community Member

callback - authorization failed

Hi !

I am trying to implement callback-solution on a Cisco 3660 (with Cisco Secure ACS) as TACACS+ Server.

A data-call is successfully established to the access-server - authenticated -

and terminated - because of callback -

the callback is initiated but fails because of a AUTHORIZATION ERROR.

I added a debug - would be nice, if anyone could give me a hint -

THX A LOT

Hans

DEBUG:

sh debug

General OS:

TACACS access control debugging is on

AAA Authentication debugging is on

AAA Authorization debugging is on

PPP:

PPP authentication debugging is on

PPP protocol negotiation debugging is on

The following ISDN debugs are enabled on all DSLs:

debug isdn error is ON.

debug isdn q931 is ON.

Callback:

Callback activity debugging is on

RAS#

RAS#

RAS#

RAS#

RAS#

RAS#

*Mar 1 01:58:13: ISDN Se1/0:15 Q931: RX <- SETUP pd = 8 callref = 0x0014

Sending Complete

Bearer Capability i = 0x8890

Standard = CCITT

Transer Capability = Unrestricted Digital

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA98395

Exclusive, Channel 21

Calling Party Number i = 0x0083, '8227'

Plan:Unknown, Type:Unknown

*Mar 1 01:58:13: AAA/ACCT/DS0: channel=20, ds1=0, t3=0, slot=1, ds0=16777236

*Mar 1 01:58:13: %LINK-3-UPDOWN: Interface Serial1/0:20, changed state to up

*Mar 1 01:58:13: ISDN Se1/0:15 Q931: TX -> CALL_PROC pd = 8 callref = 0x8014

Channel ID i = 0xA98395

Exclusive, Channel 21

*Mar 1 01:58:13: ISDN Se1/0:15 Q931: TX -> CONNECT pd = 8 callref = 0x8014

Channel ID i = 0xA98395

Exclusive, Channel 21

*Mar 1 01:58:13: Se1/0:20 PPP: Treating connection as a callin

*Mar 1 01:58:13: Se1/0:20 PPP: Phase is ESTABLISHING, Passive Open

*Mar 1 01:58:13: Se1/0:20 LCP: State is Listen

*Mar 1 01:58:13: ISDN Se1/0:15 Q931: RX <- CONNECT_ACK pd = 8 callref = 0x0014

*Mar 1 01:58:14: Se1/0:20 LCP: I CONFREQ [Listen] id 0 len 13

*Mar 1 01:58:14: Se1/0:20 LCP: MagicNumber 0x613B577B (0x0506613B577B)

*Mar 1 01:58:14: Se1/0:20 LCP: Callback 6 (0x0D0306)

*Mar 1 01:58:14: Se1/0:20 PPP: Authorization required

*Mar 1 01:58:14: Se1/0:20 LCP: O CONFREQ [Listen] id 3 len 14

*Mar 1 01:58:14: Se1/0:20 LCP: AuthProto PAP (0x0304C023)

*Mar 1 01:58:14: Se1/0:20 LCP: MagicNumber 0x07BD188E (0x050607BD188E)

*Mar 1 01:58:14: Se1/0:20 LCP: O CONFACK [Listen] id 0 len 13

*Mar 1 01:58:14: Se1/0:20 LCP: MagicNumber 0x613B577B (0x0506613B577B)

*Mar 1 01:58:14: Se1/0:20 LCP: Callback 6 (0x0D0306)

*Mar 1 01:58:14: Se1/0:20 LCP: I CONFACK [ACKsent] id 3 len 14

*Mar 1 01:58:14: Se1/0:20 LCP: AuthProto PAP (0x0304C023)

*Mar 1 01:58:14: Se1/0:20 LCP: MagicNumber 0x07BD188E (0x050607BD188E)

*Mar 1 01:58:14: Se1/0:20 LCP: State is Open

*Mar 1 01:58:14: Se1/0:20 PPP: Phase is AUTHENTICATING, by this end

*Mar 1 01:58:14: Se1/0:20 LCP: I IDENTIFY [Open] id 1 len 18 magic 0x613B577B MSRASV5.10

*Mar 1 01:58:14: Se1/0:20 LCP: I IDENTIFY [Open] id 2 len 23 magic 0x613B577B MSRAS-1-H3A0322

*Mar 1 01:58:14: Se1/0:20 PAP: I AUTH-REQ id 67 len 32 from "schimeha*2518491739"

*Mar 1 01:58:14: Se1/0:20 PAP: Authenticating peer schimeha*2518491739

*Mar 1 01:58:14: AAA/AUTHEN/PPP (00000046): Pick method list 'default'

*Mar 1 01:58:14: Se1/0:20 PPP: Sent PAP LOGIN Request to AAA

*Mar 1 01:58:14: TPLUS: Queuing AAA Authentication request 70 for processing

*Mar 1 01:58:14: TPLUS: processing authentication start request id 70

*Mar 1 01:58:14: TPLUS: Authentication start packet created for 70(schimeha*2518491739)

*Mar 1 01:58:14: TPLUS: Using server 10.129.7.140

*Mar 1 01:58:14: TPLUS(00000046): connected to server 10.129.7.140

*Mar 1 01:58:16: Se1/0:20 PAP: I AUTH-REQ id 68 len 32 from "schimeha*2518491739"

*Mar 1 01:58:16: Se1/0:20 PAP: Ignoring Additional Request

*Mar 1 01:58:16: TPLUS: response received for AAA request 70

*Mar 1 01:58:16: TPLUS: Received authen response status PASS (2)

*Mar 1 01:58:16: Se1/0:20 PPP: Received LOGIN Response from AAA = PASS

*Mar 1 01:58:16: AAA/AUTHOR (0x46): Pick method list 'default'

*Mar 1 01:58:16: Se1/0:20 PPP: Sent LCP AUTHOR Request to AAA

*Mar 1 01:58:16: AAA/AUTHOR (0x46): Pick method list 'default'

*Mar 1 01:58:16: Se1/0:20 PPP: Sent IPCP AUTHOR Request to AAA

*Mar 1 01:58:16: TPLUS: Queuing AAA Authorization request 70 for processing

*Mar 1 01:58:16: TPLUS: Queuing AAA Authorization request 70 for processing

*Mar 1 01:58:16: TPLUS: processing authorization request id 70

*Mar 1 01:58:16: TPLUS: Sending AV service=ppp

*Mar 1 01:58:16: TPLUS: Sending AV protocol=lcp

*Mar 1 01:58:16: TPLUS: Authorization request created for 70(schimeha*2518491739)

*Mar 1 01:58:16: TPLUS: using previously set server 10.129.7.140 from group tacacs+

*Mar 1 01:58:16: TPLUS(00000046): connected to server 10.129.7.140

*Mar 1 01:58:16: TPLUS: response received for AAA request 70

*Mar 1 01:58:16: TPLUS: Processed AV callback-dialstring=

*Mar 1 01:58:16: TPLUS: received authorization response for 70: PASS

*Mar 1 01:58:16: TPLUS: processing authorization request id 70

*Mar 1 01:58:16: TPLUS: Sending AV service=ppp

*Mar 1 01:58:16: TPLUS: Sending AV protocol=ip

*Mar 1 01:58:16: TPLUS: Authorization request created for 70(schimeha*2518491739)

*Mar 1 01:58:16: TPLUS: using previously set server 10.129.7.140 from group tacacs+

*Mar 1 01:58:16: Se1/0:20 LCP: Received AAA AUTHOR Response = PASS

*Mar 1 01:58:16: Se1/0:20 PPP/AAA: Check Attr: Framed-Protocol

*Mar 1 01:58:16: Se1/0:20 PPP/AAA: Check Attr: username

*Mar 1 01:58:16: Se1/0:20 PPP/AAA: Check Attr: callback-dialstring

*Mar 1 01:58:16: Se1/0:20 AAA/AUTHOR/FSM: We can start LCP

*Mar 1 01:58:16: TPLUS(00000046): connected to server 10.129.7.140

*Mar 1 01:58:16: TPLUS: response received for AAA request 70

*Mar 1 01:58:16: TPLUS: Processed AV addr=10.129.10.18

*Mar 1 01:58:16: TPLUS: received authorization response for 70: PASS

*Mar 1 01:58:16: Se1/0:20 IPCP: Received AAA AUTHOR Response = PASS

*Mar 1 01:58:16: Se1/0:20 PPP/AAA: Check Attr: Framed-Protocol

*Mar 1 01:58:16: Se1/0:20 PPP/AAA: Check Attr: username

*Mar 1 01:58:16: Se1/0:20 PPP/AAA: Check Attr: addr

*Mar 1 01:58:16: Se1/0:20 AAA/AUTHOR/FSM: We can start IPCP

*Mar 1 01:58:16: Se1/0:20 AAA/AUTHOR/LCP: Process Author

*Mar 1 01:58:16: Se1/0:20 AAA/AUTHOR/LCP: Process Attr: callback-dialstring

*Mar 1 01:58:16: Se1/0:20 PAP: O AUTH-ACK id 68 len 5

*Mar 1 01:58:16: Se1/0:20 MCB: User schimeha*2518491739 Callback Number - Client ANY

*Mar 1 01:58:16: Serial1/0:20 PPP: O MCB Request(1) id 1 len 9

*Mar 1 01:58:16: Serial1/0:20 MCB: O 1 1 0 9 2 5 0 1 0

*Mar 1 01:58:16: Se1/0:20 MCB: O Request Id 1 Callback Type Client-Num delay 0

*Mar 1 01:58:16: Se1/0:20 PPP: Phase is CBCP

*Mar 1 01:58:16: TPLUS: Queuing AAA Accounting request 70 for processing

*Mar 1 01:58:16: TPLUS: processing accounting request id 70

*Mar 1 01:58:16: TPLUS: Sending AV task_id=81

*Mar 1 01:58:16: TPLUS: Sending AV timezone=UTC

*Mar 1 01:58:16: TPLUS: Sending AV service=ppp

*Mar 1 01:58:16: TPLUS: Sending AV Framed-Protocol=1

*Mar 1 01:58:16: TPLUS: Accounting request created for 70(schimeha*2518491739)

*Mar 1 01:58:16: TPLUS: using previously set server 10.129.7.140 from group tacacs+

*Mar 1 01:58:16: TPLUS(00000046): connected to server 10.129.7.140

*Mar 1 01:58:16: TPLUS: response received for AAA request 70

*Mar 1 01:58:16: TPLUS: Received accounting response with status PASS

*Mar 1 01:58:17: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/0:20, changed state to up

*Mar 1 01:58:18: Se1/0:20 MCB: Timeout in state WAIT_RESPONSE

*Mar 1 01:58:18: Serial1/0:20 PPP: O MCB Request(1) id 2 len 9

*Mar 1 01:58:18: Serial1/0:20 MCB: O 1 2 0 9 2 5 0 1 0

*Mar 1 01:58:18: Se1/0:20 MCB: O Request Id 2 Callback Type Client-Num delay 0

*Mar 1 01:58:19: %ISDN-6-CONNECT: Interface Serial1/0:20 is now connected to 8227 schimeha*2518491739

*Mar 1 01:58:20: Se1/0:20 MCB: Timeout in state WAIT_RESPONSE

*Mar 1 01:58:20: Serial1/0:20 PPP: O MCB Request(1) id 3 len 9

*Mar 1 01:58:20: Serial1/0:20 MCB: O 1 3 0 9 2 5 0 1 0

*Mar 1 01:58:20: Se1/0:20 MCB: O Request Id 3 Callback Type Client-Num delay 0

*Mar 1 01:58:22: Se1/0:20 MCB: Timeout in state WAIT_RESPONSE

*Mar 1 01:58:22: Serial1/0:20 PPP: O MCB Request(1) id 4 len 9

*Mar 1 01:58:22: Serial1/0:20 MCB: O 1 4 0 9 2 5 0 1 0

*Mar 1 01:58:22: Se1/0:20 MCB: O Request Id 4 Callback Type Client-Num delay 0

RAS#

RAS#

RAS#

RAS#

RAS#

RAS#

RAS#

RAS#

RAS#

RAS#

RAS#

*Mar 1 01:58:24: Se1/0:20 MCB: Timeout in state WAIT_RESPONSE

*Mar 1 01:58:24: Serial1/0:20 PPP: O MCB Request(1) id 5 len 9

*Mar 1 01:58:24: Serial1/0:20 MCB: O 1 5 0 9 2 5 0 1 0

*Mar 1 01:58:24: Se1/0:20 MCB: O Request Id 5 Callback Type Client-Num delay 0

*Mar 1 01:58:26: Se1/0:20 MCB: Timeout in state WAIT_RESPONSE

*Mar 1 01:58:26: Serial1/0:20 PPP: O MCB Request(1) id 6 len 9

*Mar 1 01:58:26: Serial1/0:20 MCB: O 1 6 0 9 2 5 0 1 0

*Mar 1 01:58:26: Se1/0:20 MCB: O Request Id 6 Callback Type Client-Num delay 0

*Mar 1 01:58:28: Serial1/0:20 PPP: I MCB Response(2) id 6 len 13

*Mar 1 01:58:28: Serial1/0:20 MCB: I 2 6 0 D 2 9 A 1 38 32 32 37 0

*Mar 1 01:58:28: Se1/0:20 MCB: Received response

*Mar 1 01:58:28: Se1/0:20 MCB: Response CBK-Client-Num 2 9 10, addr 1-8227

*Mar 1 01:58:28: Serial1/0:20 PPP: O MCB Ack(3) id 7 len 13

*Mar 1 01:58:28: Serial1/0:20 MCB: O 3 7 0 D 2 9 A 1 38 32 32 37 0

*Mar 1 01:58:28: Se1/0:20 MCB: O Ack Id 7 Callback Type Client-Num delay 10

*Mar 1 01:58:28: Se1/0:20 MCB: Negotiated MCB with peer

*Mar 1 01:58:28: Se1/0:20 LCP: I TERMREQ [Open] id 3 len 16 (0x613B577B003CCD7400000000)

*Mar 1 01:58:28: Se1/0:20 LCP: O TERMACK [Open] id 3 len 4

*Mar 1 01:58:28: Se1/0:20 MCB: Peer terminating the link

*Mar 1 01:58:28: Se1/0:20 MCB: Link terminated by peer, Callback Needed

*Mar 1 01:58:28: Se1/0:20 MCB: Initiate Callback for ^->o`lLD at 8227 using ISDN DDR

*Mar 1 01:58:28: Se1/0:20 PPP/AAA: Saving a copy of the authorization data

*Mar 1 01:58:28: Se1/0:20 PPP: Phase is TERMINATING

*Mar 1 01:58:28: TPLUS: Queuing AAA Accounting request 70 for processing

*Mar 1 01:58:28: TPLUS: processing accounting request id 70

*Mar 1 01:58:28: TPLUS: Sending AV task_id=81

*Mar 1 01:58:28: TPLUS: Sending AV timezone=UTC

*Mar 1 01:58:28: TPLUS: Sending AV service=ppp

*Mar 1 01:58:28: TPLUS: Sending AV Framed-Protocol=1

*Mar 1 01:58:28: TPLUS: Sending AV pre-session-time=3

*Mar 1 01:58:28: TPLUS: Sending AV nas-tx-speed=64000

*Mar 1 01:58:28: TPLUS: Sending AV nas-rx-speed=64000

*Mar 1 01:58:28: TPLUS: Sending AV elapsed_time=12

*Mar 1 01:58:28: TPLUS: Sending AV bytes_in=37

*Mar 1 01:58:28: TPLUS: Sending AV bytes_out=90

*Mar 1 01:58:28: TPLUS: Sending AV paks_in=2

*Mar 1 01:58:28: TPLUS: Sending AV paks_out=7

*Mar 1 01:58:28: TPLUS: Sending AV disc-cause=1

*Mar 1 01:58:28: TPLUS: Accounting request created for 70(schimeha*2518491739)

*Mar 1 01:58:28: TPLUS: using previously set server 10.129.7.140 from group tacacs+

*Mar 1 01:58:28: TPLUS(00000046): connected to server 10.129.7.140

*Mar 1 01:58:28: TPLUS: response received for AAA request 70

*Mar 1 01:58:28: TPLUS: Received accounting response with status PASS

*Mar 1 01:58:28: ISDN Se1/0:15 Q931: RX <- DISCONNECT pd = 8 callref = 0x0014

Cause i = 0x8090 - Normal call clearing

Progress Ind i = 0x8088 - In-band info or appropriate now available

*Mar 1 01:58:28: %ISDN-6-DISCONNECT: Interface Serial1/0:20 disconnected from 8227 schimeha*2518491739, call lasted 14 seconds

*Mar 1 01:58:28: %LINK-3-UPDOWN: Interface Serial1/0:20, changed state to down

*Mar 1 01:58:28: ISDN Se1/0:15 Q931: TX -> RELEASE pd = 8 callref = 0x8014

*Mar 1 01:58:28: Se1/0:20 LCP: State is Closed

*Mar 1 01:58:28: Se1/0:20 PPP: Phase is DOWN

*Mar 1 01:58:28: ISDN Se1/0:15 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x0014

Cause i = 0x8090 - Normal call clearing

*Mar 1 01:58:29: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/0:20, changed state to down

RAS#

RAS#

RAS#

RAS#

RAS#

RAS#

RAS#

RAS#

RAS#

RAS#

RAS#

RAS#

RAS#

RAS#

RAS#

RAS#

RAS#

*Mar 1 01:58:43: ISDN Se1/0:15 Q931: TX -> SETUP pd = 8 callref = 0x000A

Bearer Capability i = 0x8890

Standard = CCITT

Transer Capability = Unrestricted Digital

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA9839F

Exclusive, Channel 31

Called Party Number i = 0x81, '8227'

Plan:ISDN, Type:Unknown

*Mar 1 01:58:43: ISDN Se1/0:15 Q931: RX <- SETUP_ACK pd = 8 callref = 0x800A

Channel ID i = 0xA9839F

Exclusive, Channel 31

*Mar 1 01:58:43: ISDN Se1/0:15 Q931: RX <- CALL_PROC pd = 8 callref = 0x800A

Channel ID i = 0xA9839F

Exclusive, Channel 31

*Mar 1 01:58:43: ISDN Se1/0:15 Q931: RX <- ALERTING pd = 8 callref = 0x800A

Progress Ind i = 0x8088 - In-band info or appropriate now available

*Mar 1 01:58:43: ISDN Se1/0:15 Q931: RX <- CONNECT pd = 8 callref = 0x800A

Date/Time i = 0x0209180F27

Connected Number i = 0x118034333138323237

*Mar 1 01:58:44: %LINK-3-UPDOWN: Interface Serial1/0:30, changed state to up

*Mar 1 01:58:44: Se1/0:30 PPP/AAA: Using authorization data from a prior call

*Mar 1 01:58:44: ISDN Se1/0:15 Q931: TX -> CONNECT_ACK pd = 8 callref = 0x000A

*Mar 1 01:58:44: Se1/0:30 PPP: Treating connection as a callout

*Mar 1 01:58:44: Se1/0:30 PPP: Phase is ESTABLISHING, Active Open

*Mar 1 01:58:44: Se1/0:30 PPP: Authorization required

*Mar 1 01:58:44: Se1/0:30 PPP: No remote authentication for callback

*Mar 1 01:58:44: Se1/0:30 AAA/AUTHOR/LCP: Authorization succeeds trivially

*Mar 1 01:58:44: Se1/0:30 LCP: O CONFREQ [Closed] id 18 len 10

*Mar 1 01:58:44: Se1/0:30 LCP: MagicNumber 0x07BD8CF6 (0x050607BD8CF6)

*Mar 1 01:58:44: Se1/0:30 LCP: I CONFACK [REQsent] id 18 len 10

*Mar 1 01:58:44: Se1/0:30 LCP: MagicNumber 0x07BD8CF6 (0x050607BD8CF6)

*Mar 1 01:58:45: Se1/0:30 LCP: I CONFREQ [ACKrcvd] id 1 len 10

*Mar 1 01:58:45: Se1/0:30 LCP: MagicNumber 0x5CA36BF7 (0x05065CA36BF7)

*Mar 1 01:58:45: Se1/0:30 LCP: O CONFACK [ACKrcvd] id 1 len 10

*Mar 1 01:58:45: Se1/0:30 LCP: MagicNumber 0x5CA36BF7 (0x05065CA36BF7)

*Mar 1 01:58:45: Se1/0:30 LCP: State is Open

*Mar 1 01:58:45: AAA/AUTHOR (0x47): Pick method list 'default'

*Mar 1 01:58:45: Se1/0:30 PPP: Sent LCP AUTHOR Request to AAA

*Mar 1 01:58:45: AAA/AUTHOR (0x47): Pick method list 'default'

*Mar 1 01:58:45: Se1/0:30 PPP: Sent IPCP AUTHOR Request to AAA

*Mar 1 01:58:45: TPLUS: Queuing AAA Authorization request 71 for processing

*Mar 1 01:58:45: TPLUS: Queuing AAA Authorization request 71 for processing

*Mar 1 01:58:45: TPLUS: processing authorization request id 71

*Mar 1 01:58:45: TPLUS: Sending AV service=ppp

*Mar 1 01:58:45: TPLUS: Sending AV protocol=lcp

*Mar 1 01:58:45: TPLUS: Authorization request created for 71(RAS)

*Mar 1 01:58:45: TPLUS: Using server 10.129.7.140

*Mar 1 01:58:45: TPLUS(00000047): connected to server 10.129.7.140

*Mar 1 01:58:45: TPLUS: response received for AAA request 71

*Mar 1 01:58:45: TPLUS: received authorization response for 71: FAIL

*Mar 1 01:58:45: TPLUS: processing authorization request id 71

*Mar 1 01:58:45: TPLUS: Sending AV service=ppp

*Mar 1 01:58:45: TPLUS: Sending AV protocol=ip

*Mar 1 01:58:45: TPLUS: Authorization request created for 71(RAS)

*Mar 1 01:58:45: TPLUS: using previously set server 10.129.7.140 from group tacacs+

*Mar 1 01:58:45: Se1/0:30 LCP: Received AAA AUTHOR Response = FAIL

*Mar 1 01:58:45: Se1/0:30 AAA/AUTHOR/FSM: We cannot start LCP

*Mar 1 01:58:45: Se1/0:30 PPP: Phase is TERMINATING

*Mar 1 01:58:45: Se1/0:30 LCP: O TERMREQ [Open] id 19 len 4

*Mar 1 01:58:45: TPLUS(00000047): connected to server 10.129.7.140

*Mar 1 01:58:45: TPLUS: response received for AAA request 71

*Mar 1 01:58:45: TPLUS: received authorization response for 71: FAIL

*Mar 1 01:58:46: Se1/0:30 LCP: I IDENTIFY [TERMsent] id 2 len 18 magic 0x5CA36BF7 MSRASV5.10

*Mar 1 01:58:46: Se1/0:30 LCP: I IDENTIFY [TERMsent] id 3 len 23 magic 0x5CA36BF7 MSRAS-1-H3A0322

*Mar 1 01:58:46: ISDN Se1/0:15 Q931: RX <- DISCONNECT pd = 8 callref = 0x800A

Cause i = 0x8090 - Normal call clearing

Progress Ind i = 0x8088 - In-band info or appropriate now available

*Mar 1 01:58:46: %ISDN-6-CONNECT: Interface Serial1/0:30 is now connected to 8227

*Mar 1 01:58:46: %ISDN-6-DISCONNECT: Interface Serial1/0:30 disconnected from 8227 , call lasted 2 seconds

*Mar 1 01:58:46: %LINK-3-UPDOWN: Interface Serial1/0:30, changed state to down

*Mar 1 01:58:46: ISDN Se1/0:15 Q931: TX -> RELEASE pd = 8 callref = 0x000A

*Mar 1 01:58:46: Se1/0:30 LCP: State is Closed

*Mar 1 01:58:46: Se1/0:30 PPP: Phase is DOWN

*Mar 1 01:58:46: ISDN Se1/0:15 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x800A

Cause i = 0x8090 - Normal call clearing

1 REPLY
Bronze

Re: callback - authorization failed

I would suggest that you open a case with the TAC; this looks like it may be a new bug.

It appears that you are running some very recent 12.2T code; a routine was added to make a copy of the authorization data. However, it looks like that copy was either lost or not referenced for the callback. The important debug is here:

*Mar 1 01:58:28: Se1/0:20 PPP/AAA: Saving a copy of the authorization data

*Mar 1 01:58:44: Se1/0:30 PPP/AAA: Using authorization data from a prior call

It looks like we don't use the authorization data, though; it looks like we go back to the AAA server, where that fails again.

Sorry, but I can't think of a possible workaround at this point.

291
Views
0
Helpful
1
Replies
CreatePlease to create content