Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Community Member

can i check the GBIC type on catalyst 3550 by console ?

my customer has a running catalyst 3550.

he asked for me to check the GBIC type by console.

is it possible to check it ? if yes, how to do it ?

thanks

1 ACCEPTED SOLUTION

Accepted Solutions
Gold

Re: can i check the GBIC type on catalyst 3550 by console ?

On a Cisco IOS switch, run "show interface GigabitEthernet 0/x" where "x" is the number of the port. You should see something like this in the output:

Auto-duplex (Full), 1000Mb/s, media type is SX

Auto-duplex (Full), 1000Mb/s, media type is LX

On a Catalyst OS switch, run "show port x/y" where "x" is the slot the module is in, and "y" is the port where the GBIC is. (Run "show port" to see all ports.) You should see something like this:

Port Name Status Vlan Duplex Speed Type

----- ------------------ ---------- ---------- ------ ----- ------------

1/1 connected trunk full 1000 1000BaseSX

1/2 connected trunk full 1000 1000BaseSX

3/1 connected trunk full 1000 1000-LX/LH

3/2 connected trunk full 1000 1000-LX/LH

3/3 connected trunk full 1000 1000-LX/LH

3/4 connected trunk full 1000 1000-LX/LH

3/5 connected trunk full 1000 1000-LX/LH

3/6 connected trunk full 1000 1000-LX/LH

3/7 connected trunk full 1000 1000-LX/LH

3/8 connected trunk full 1000 1000-LX/LH

3/9 connected trunk full 1000 1000-LX/LH

3/10 notconnect 1 full 1000 No GBIC

3/11 notconnect 1 full 1000 No GBIC

3/12 notconnect 1 full 1000 No GBIC

3/13 notconnect 1 full 1000 No GBIC

3/14 notconnect 1 full 1000 No GBIC

3/15 connected trunk full 1000 1000BaseSX

3/16 connected trunk full 1000 1000BaseSX

Hope this helps.

1 REPLY
Gold

Re: can i check the GBIC type on catalyst 3550 by console ?

On a Cisco IOS switch, run "show interface GigabitEthernet 0/x" where "x" is the number of the port. You should see something like this in the output:

Auto-duplex (Full), 1000Mb/s, media type is SX

Auto-duplex (Full), 1000Mb/s, media type is LX

On a Catalyst OS switch, run "show port x/y" where "x" is the slot the module is in, and "y" is the port where the GBIC is. (Run "show port" to see all ports.) You should see something like this:

Port Name Status Vlan Duplex Speed Type

----- ------------------ ---------- ---------- ------ ----- ------------

1/1 connected trunk full 1000 1000BaseSX

1/2 connected trunk full 1000 1000BaseSX

3/1 connected trunk full 1000 1000-LX/LH

3/2 connected trunk full 1000 1000-LX/LH

3/3 connected trunk full 1000 1000-LX/LH

3/4 connected trunk full 1000 1000-LX/LH

3/5 connected trunk full 1000 1000-LX/LH

3/6 connected trunk full 1000 1000-LX/LH

3/7 connected trunk full 1000 1000-LX/LH

3/8 connected trunk full 1000 1000-LX/LH

3/9 connected trunk full 1000 1000-LX/LH

3/10 notconnect 1 full 1000 No GBIC

3/11 notconnect 1 full 1000 No GBIC

3/12 notconnect 1 full 1000 No GBIC

3/13 notconnect 1 full 1000 No GBIC

3/14 notconnect 1 full 1000 No GBIC

3/15 connected trunk full 1000 1000BaseSX

3/16 connected trunk full 1000 1000BaseSX

Hope this helps.

298
Views
0
Helpful
1
Replies
CreatePlease to create content