09-27-2002 12:10 AM - edited 03-02-2019 01:41 AM
When trying to delete a dialer from the configuration of a cisco 2600 I get the following error:-
%Remove dialing ddb from profile first
Does anybody know what this means and how I can remove the config without rebooting the router? I cant find any bug on the cisco tac.
I tried deleting dialer 100 from the config below:-
isdn switch-type vn3
isdn voice-call-failure 0
!
!
!
interface Loopback0
ip address 10.254.155.1 255.255.255.0
!
interface Loopback1
ip address 10.253.155.1 255.255.0.0
!
interface Ethernet0/0
ip address 10.155.1.1 255.255.0.0
ip helper-address 10.150.3.2
ip helper-address 10.152.3.2
ip helper-address 10.153.3.2
no cdp enable
!
interface BRI0/0
description Backup to Marotis & Swindon
bandwidth 10
no ip address
encapsulation ppp
dialer pool-member 1
isdn switch-type vn3
isdn static-tei 60
no cdp enable
ppp authentication chap
!
interface Serial0/0
description Link to Chitraco1
bandwidth 2048
ip unnumbered Loopback0
encapsulation ppp
no ip mroute-cache
no cdp enable
!
interface Dialer1
description Backup to Marotis
bandwidth 10
ip unnumbered Loopback1
encapsulation ppp
dialer pool 1
dialer remote-name PRI
dialer idle-timeout 60
dialer string 039350445
dialer string 00441793360124
dialer-group 1
no cdp enable
ppp authentication chap
ppp chap hostname LSD
ppp chap password 7 xxxxxxxxxxxx
!
interface Dialer100
description test interface
ip unnumbered Loopback1
dialer pool 1
dialer remote-name test
no cdp enable
!
router eigrp 1
passive-interface Dialer1
network 10.155.0.0 0.0.255.255
network 10.253.0.0 0.0.255.255
network 10.254.155.0 0.0.0.255
no auto-summary
no eigrp log-neighbor-changes
!
no ip classless
ip route 0.0.0.0 0.0.0.0 Dialer1 200
no ip http server
!
access-list 2 permit 148.185.164.28
access-list 2 permit 10.254.0.0 0.0.255.255
access-list 101 deny eigrp any any
access-list 101 deny udp any any eq ntp
access-list 101 permit ip any any
dialer-list 1 protocol ip list 10
LSD#sh vers
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 12.1(7), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2001 by cisco Systems, Inc.
Compiled Thu 22-Feb-01 12:50 by kellythw
Image text-base: 0x80008088, data-base: 0x808023C4
ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
LSD uptime is 4 weeks, 3 days, 1 hour, 31 minutes
System returned to ROM by power-on
System restarted at 06:36:18 BST Tue Aug 27 2002
System image file is "flash:c2600-i-mz.121-7"
cisco 2610 (MPC860) processor (revision 0x203) with 26624K/6144K bytes of memory.
Processor board ID JAD05390F7K (2418368399)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
Basic Rate ISDN software, Version 1.1.
1 Ethernet/IEEE 802.3 interface(s)
1 Serial network interface(s)
1 ISDN Basic Rate interface(s)
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
Many Thanks
Tom
09-27-2002 12:49 AM
you need to remove 1) dialer pool 1 and dialer-group 1 from dialer interface.
09-27-2002 01:22 AM
I get this error when I type no dialer pool 1 under the dialer:-
LSD#conf t
Enter configuration commands, one per line. End with CNTL/Z.
LSD(config)#int d 100
LSD(config-if)#no dialer pool
LSD(config-if)#no dialer pool 1
%Remove dialing ddb from profile first
LSD(config-if)#LSD#sh run int d 100
Building configuration...
Current configuration : 135 bytes
!
interface Dialer100
description test interface
ip unnumbered Loopback1
dialer pool 1
dialer remote-name test
no cdp enable
end
thanks
Tom
09-27-2002 02:53 AM
i would recommend you to remove all Dialer relationship commands between physical interfaces and Dialer interface such as DIALER-POOL, DIALER-GROUP. After checking there is no relation between them then remove DIALER INTERFACE.
09-27-2002 04:49 AM
check if the commandis is using in the router.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: