Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Cat2900 M CRC errors

hello

i have been receiving a lot of crc errors on a fiber module port. i have replace the fiber patch cable and even went so far as to replace the 4 port fiber card. i can't get a handle on where they are coming from. the other end is connected to a 2900M as well. i only see a larger number of crc on the one interface.

FastEthernet2/2 is up, line protocol is up

Hardware is Fast Ethernet, address is 0003.e393.c468 (bia 0003.e393.c467)

MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,

reliability 255/255, txload 2/255, rxload 1/255

Encapsulation ARPA, loopback not set

Keepalive not set

Full-duplex, 100Mb/s

ARP type: ARPA, ARP Timeout 04:00:00

Last input 00:00:10, output 00:00:00, output hang never

Last clearing of "show interface" counters 07:23:38

Queueing strategy: fifo

Output queue 0/40, 0 drops; input queue 0/75, 0 drops

5 minute input rate 505000 bits/sec, 170 packets/sec

5 minute output rate 828000 bits/sec, 5 packets/sec

3700127 packets input, 1273379232 bytes

Received 6404 broadcasts, 0 runts, 0 giants, 0 throttles

1095 input errors, 1094 CRC, 1 frame, 38 overrun, 39 ignored

0 watchdog, 560 multicast

0 input packets with dribble condition detected

144957 packets output, 2261653952 bytes, 0 underruns

0 output errors, 0 collisions, 2 interface resets

0 babbles, 0 late collision, 0 deferred

0 lost carrier, 0 no carrier

0 output buffer failures, 0 output buffers swapped out

any help in pointing me in the right direction would be greatly appreciated.

thanks

Steve

  • Other Network Infrastructure Subjects
5 REPLIES
Silver

Re: Cat2900 M CRC errors

I would check the device it is connected to , make sure it is also hard coded to 100 full duplex , no auto negotiation

New Member

Re: Cat2900 M CRC errors

i havd checked that previously.....here is the other port:

FastEthernet2/1 is up, line protocol is up

Hardware is Fast Ethernet, address is 0090.f230.e2dd (bia 0090.f230.e2dd)

MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, rely 255/255, load 1/255

Encapsulation ARPA, loopback not set, keepalive not set

Full-duplex, 100Mb/s

ARP type: ARPA, ARP Timeout 04:00:00

Last input 00:00:00, output 00:38:40, output hang never

Last clearing of "show interface" counters 3w1d

Queueing strategy: fifo

Output queue 0/40, 0 drops; input queue 0/75, 0 drops

5 minute input rate 1026000 bits/sec, 377 packets/sec

5 minute output rate 618000 bits/sec, 343 packets/sec

275155144 packets input, 3501740008 bytes, 0 no buffer

Received 7773150 broadcasts, 0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 367 ignored, 0 abort

0 watchdog, 1723804 multicast

0 input packets with dribble condition detected

266189068 packets output, 1201088733 bytes, 0 underruns

0 output errors, 0 collisions, 0 interface resets

0 babbles, 0 late collision, 0 deferred

0 lost carrier, 0 no carrier

0 output buffer failures, 0 output buffers swapped out

Bronze

Re: Cat2900 M CRC errors

Do you have the luxury of a second fiber pair that you can swap to for this connection?

Mark

New Member

Re: Cat2900 M CRC errors

yes i do have some spare dark fibers.....that was going to be my next step, but i wanted to make sure i wasn't overlooking something obvious before i go to the trouble of terminating the spare fiber

thanks

steve.

Silver

Re: Cat2900 M CRC errors

before you go through the trouble of swapping fiber , I would try to bounce the interface on each side , sometimes the interfaces need to be bounced for the speed & duplex is changed .

170
Views
0
Helpful
5
Replies