Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements
You may experience some slow load times, errors, and slight inconsistencies. We ask for your patience as we finalize the launch. Thank you.

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Cat4006 Error Message

2003 Aug 02 07:32:39 %SYS-4-P2_WARN: 1/Lemans(2/3) - timeout occurred

2003 Aug 02 07:32:50 %SYS-4-P2_WARN: 1/Astro(4/3) - timeout occurred

These error messages occurred on a Cat4006 w/ Sup II this weekend causing part of my network to drop. Although resetting the switch fixed the problem, I am going to have questions on Monday as to why it happened. The website says that it means the Supervisor lost communication with a component on a 10/100 card but doesn't explain much more than that. Has anyone seen this error before and can explain to me where to start looking for the cause? Everything I see on the show tech looks good but obviously something happened.

Thank you.

  • Other Network Infrastructure Subjects
3 REPLIES
Cisco Employee

Re: Cat4006 Error Message

Previous thread should help you

http://forums.cisco.com/eforum/servlet/NetProf?page=netprof&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.ee8fa31

Were you seeing Astro errors only for few cards or all cards? Can you paste the output of sh mod?

New Member

Re: Cat4006 Error Message

Funny my search for this information didn't show that link. Thanks. This show module was taken right before I rebooted the switch:

****************** show module ******************

Mod Slot Ports Module-Type Model Sub Status

--- ---- ----- ------------------------- ------------------- --- --------

1 1 2 1000BaseX Supervisor WS-X4013 no ok

2 2 24 10/100/1000 Ethernet WS-X4424-GB-RJ45 no ok

4 4 48 Inline Power Module WS-X4148-RJ45V no ok

Mod Module-Name Serial-Num

--- -------------------- --------------------

1 JAE062302WE

2 JAB063607D5

4 JAE063409XD

Mod MAC-Address(es) Hw Fw Sw

--- -------------------------------------- ------ ---------- -----------------

1 00-09-e8-06-e4-00 to 00-09-e8-06-e7-ff 3.2 5.4(1) 6.3(5)

2 00-08-e3-a8-d2-a8 to 00-08-e3-a8-d2-bf 1.5

4 00-0a-b7-77-07-00 to 00-0a-b7-77-07-2f 2.6

The error messages were reported on only 2 ports:

Astro on 4/3 & 4/4 while the Lemans error was on 2/3 and 2/4

I'll try swapping the module around the next time we have the error come up. As far as a spanning-tree loop, I'm investigating a possible problem but haven't discovered anything concrete yet.

New Member

Re: Cat4006 Error Message

Hello,

We had problems with our 4006 on Sunday generating the Astro message, but unfortunately it was reloaded before I could record the message. On reloading, the switch stayed down until I powered off the switch and re-seated the Supervisor (SEIII) module. I would be interested to know if spanning tree is an issue as we have replaced this switch in the last 3-6 months because of this problem.

Thank you

87
Views
0
Helpful
3
Replies