Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

CAT5505 show test(Unknow)

Hi Guys,

I am having the out below. I am not sure whether it will cause any problem later?

Did you guys see the msg with unknow status? Thanks.

Coreswitch> (enable) sh test

Diagnostic mode: complete (mode at next reset: complete)

Environmental Status (. = Pass, F = Fail, U = Unknown, N = Not Present)

PS (3.3V): . PS (12V): . PS (24V): . PS1: . PS2: .

Temperature: . Fan: . Clock(A/B): A Chassis-Ser-EEPROM: .

Module 1 : 0-port Supervisor III

Network Management Processor (NMP) Status: (. = Pass, F = Fail, U = Unknown)

ROM: . Flash-EEPROM: . Ser-EEPROM: . NVRAM: . MCP Comm: .

EARL II Status :

DisableIndexLearnTest: U

DontLearnTest: U

DisableNewLearnTest: U

ConditionalLearnTest: U

MonitorColorFloodTest: U

EarlTrapTest: U

StaticMacAndTypeTest: U

BadDvlanTest: U

BadBpduTest: U

IndexMatchTest: U

ProtocolTypeTest: U

IgmpTest: U

SourceMissTest: U

SourceModifiedTest: U

ArpaToArpaShortcutTest: U

ArpaToSnapShortcutTest: U

SnapToArpaShortcutTest: U

SnapToSnapShortcutTest: U

SoftwareShortcutTest: U

MulticastExpansionTest: U

DontShortcutTest: U

ShortcutTableFullTest: U

Line Card Diag Status for Module 1 (. = Pass, F = Fail, N = N/A)

CPU : . Sprom : . Bootcsum : . Archsum : .

RAM : . LTL : . CBL : N DPRAM : . SAMBA : N

Saints : . Pkt Bufs : . Repeater : N FLASH : .

Phoenix : . TrafficMeter: . UplinkSprom : . PhoenixSprom: .

SAINT/SAGE Status :

PHOENIX Port Status :

Ports 9 17 18 19 20 21 22

INBAND A->B B->A B->C C->B A->C C->A

------------------------------------------

. . . . . . .

Packet Buffer Status :

PHOENIX Packet Buffer Status :

Ports INBAND A<->B B<->C A<->C

------------------------------

. . . .

Loopback Status [Reported by Module 1] :

Ports 1 2 9

--------------

U U .

Coreswitch> (enable) sh ver

WS-C5505 Software, Version McpSW: 5.5(18) NmpSW: 5.5(18)

Copyright (c) 1995-2002 by Cisco Systems

NMP S/W compiled on Dec 16 2002, 15:34:48

MCP S/W compiled on Dec 16 2002, 15:30:03

System Bootstrap Version: 3.1.2

Hardware Version: 1.0 Model: WS-C5505 Serial #: 066531428

Mod Port Model Serial # Versions

--- ---- ---------- --------- ----------------------------------------

1 0 WS-X5530 010825537 Hw : 1.9

Fw : 3.1.2

Fw1: 4.2(1)

Sw : 5.5(18)

WS-F5521 010823620 Hw : 1.1

2 12 WS-X5201R 020423476 Hw : 3.1

Fw : 4.3(1)

Sw : 5.5(18)

3 24 WS-X5225R 011473297 Hw : 2.0

Fw : 4.1(1)

Sw : 5.5(18)

4 24 WS-X5225R 011571347 Hw : 2.0

Fw : 4.1(1)

Sw : 5.5(18)

5 12 WS-X5201R 010844621 Hw : 1.2

Fw : 4.1(1)

Sw : 5.5(18)

DRAM FLASH NVRAM

Module Total Used Free Total Used Free Total Used Free

------ ------- ------- ------- ------- ------- ------- ----- ----- -----

1 32768K 19892K 12876K 8192K 5629K 2563K 512K 205K 307K

Uptime is 66 days, 19 hours, 9 minutes

1 REPLY
Cisco Employee

Re: CAT5505 show test(Unknow)

Since you do not have an uplink module in the Sup3, all the related tests of uplink module are "U". What you are seeing is normal and there is nothing to worry.

133
Views
0
Helpful
1
Replies