04-23-2003 01:50 AM - edited 03-02-2019 06:49 AM
Hello,
I have a Cat6503 and want to check the imageversion for the msfc2 card, but find any output commands.
I'm not sure if Sup2Vis works fine, because there is no 'slot info' for msfc2.
Thanks for help
Ruedi
sh vers and sh modul output below.
-------------------------------------------------------------------
Router#sh ver
Cisco Internetwork Operating System Software
IOS (tm) c6sup2_rp Software (c6sup2_rp-JK9SV-M), Version 12.2(9)YO3, EARLY DEPLO
YMENT RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Thu 06-Feb-03 12:49 by eaarmas
Image text-base: 0x40008968, data-base: 0x41942000
ROM: System Bootstrap, Version 12.1(11r)E1, RELEASE SOFTWARE (fc1)
BOOTLDR: c6sup2_rp Software (c6sup2_rp-JK9SV-M), Version 12.2(9)YO3, EARLY DEPLO
YMENT RELEASE SOFTWARE (fc1)
Router uptime is 34 minutes
System returned to ROM by power-on (SP by power-on)
System image file is "bootflash:c6k222-jk9sv-mz.122-9.YO3.bin"
cisco Catalyst 6000 (R7000) processor with 489472K/34816K bytes of memory.
Processor board ID SAD062402E8
R7000 CPU at 300Mhz, Implementation 39, Rev 3.3, 256KB L2, 1024KB L3 Cache
Last reset from power-on
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
2 Virtual Ethernet/IEEE 802.3 interface(s)
4 Gigabit Ethernet/IEEE 802.3 interface(s)
381K bytes of non-volatile configuration memory.
32768K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102
Router#sh mod
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 2 Catalyst 6000 supervisor 2 (Active) WS-X6K-SUP2-2GE D0709020U
2 2 IPSec VPN Accelerator WS-SVC-IPSEC-1 SAD071300MA
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 0001.c9db.9594 to 0001.c9db.9595 4.2 6.1(3) 6.2(2.107) Ok
2 0002.7ee5.2060 to 0002.7ee5.2063 1.1 7.2(1) 6.2(2.107) Ok
Mod Sub-Module Model Serial Hw Status
--- --------------------------- --------------- --------------- ------- -------
1 Policy Feature Card 2 WS-F6K-PFC2 SAD07080136 3.3 Ok
1 Cat6k MSFC 2 daughterboard WS-F6K-MSFC2 SAD062402E8 2.4 Ok
Router#
-------------------------------------------------------------------
04-23-2003 07:30 AM
I do not understand your question. The software version you are running is 122-9.YO3. You are running native IOS and you can access slot0: using "dir slot0:"
04-23-2003 11:28 PM
Yes that's right, but I found a bootfile c6msfc2-boot-mz on bootflash: (not sup-bootflash: ) as well, therefore my question. But now it's ok.
Thanks for your help. Ruedi
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: