10-02-2006 07:18 AM - edited 03-03-2019 05:20 AM
Good day all!
I am new in Cisco world and try to configure a trunk between a Catalyst 2960 switch and a IBM Blade Center IGESM switch (manifactured by Cisco).
Unfortunately, it seems that the network traffic doesn't cross the trunk link.
I have followed (at least, I think so) the instructions given on the different Cisco documentation papers but I can't find the mistake in my configuration (lack of experience :-( !).
Both switches are using IOS. 2960 uses IOS 12.2(25)FX and IGESM uses IOS 12.2(22)EA8.
The ports are connected through a cross-over cable Cat5e.
Please find below the configuration for each ports:
Catalyst 2960:
--------------
Name: Gi0/1
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: dot1q
Negotiation of Trunking: On
Access Mode VLAN: 200 (Workstation VLAN)
Trunking Native Mode VLAN: 200 (Workstation VLAN)
Administrative Native VLAN tagging: enabled
Voice VLAN: none
Administrative private-vlan host-association: none
Administrative private-vlan mapping: none
Administrative private-vlan trunk native VLAN: none
Administrative private-vlan trunk Native VLAN tagging: enabled
Administrative private-vlan trunk encapsulation: dot1q
Administrative private-vlan trunk normal VLANs: none
Administrative private-vlan trunk private VLANs: none
Operational private-vlan: none
Trunking VLANs Enabled: 1,99,200
Pruning VLANs Enabled: 2-1001
Capture Mode Disabled
Capture VLANs Allowed: ALL
Protected: false
Unknown unicast blocked: disabled
Unknown multicast blocked: disabled
Appliance trust: none
IBM/Cisco IGESM:
----------------
Name: Gi0/20
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: dot1q
Negotiation of Trunking: On
Access Mode VLAN: 200 (Workstation VLAN)
Trunking Native Mode VLAN: 200 (Workstation VLAN)
Voice VLAN: none
Administrative private-vlan host-association: none
Administrative private-vlan mapping: none
Administrative private-vlan trunk native VLAN: none
Administrative private-vlan trunk encapsulation: dot1q
Administrative private-vlan trunk normal VLANs: none
Administrative private-vlan trunk private VLANs: none
Operational private-vlan: none
Trunking VLANs Enabled: 1,99,200
Pruning VLANs Enabled: 2-1001
Capture Mode Disabled
Capture VLANs Allowed: ALL
Protected: false
Unknown unicast blocked: disabled
Unknown multicast blocked: disabled
Appliance trust: none
For my test, I try to ping a blade (connected to IGESM) in VLAN 200 from a workstation connected to Catalyst 2960 (in VLAN 200 too). From a network anaylser (ethereal), I can see the ARP broadcast from each side but none are going across the trunk link.
I am a bit lost about this problem and would be grateful for any assistance in solving it!
Many, many thanks in advance for your time!
Best regards,
Fabian
Solved! Go to Solution.
10-04-2006 11:13 AM
Gigabit has to have all 8 wires , anything less will not work as it balanced across all 4 pairs .
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: