Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 

Cisco 6506 unable to detect modules

Hi,

I have a 6506 with SUP1 MSFC2, running IOS.

Module 1: WS-X6K-SUP1A-2GE

Module 2: Removed

Module 3: WS-X6348

Module 4: WS-X6348

Module 5: WS-X6408A-GBIC

Module 6: WS-X6408A-GBIC

However, its not able to detect the switch module.

Could this be a hardware issue?

Router#show module

Mod Ports Card Type                              Model              Serial No.

--- ----- -------------------------------------- ------------------ -----------

  1    2  Cat 6000 sup 1 Enhanced QoS (Active)   WS-X6K-SUP1A-2GE   SAD05010NXB  <======= Only IOS Supervisor is detected

Mod MAC addresses                       Hw    Fw           Sw           Status

--- ---------------------------------- ------ ------------ ------------ -------

  1  0003.3282.4f3a to 0003.3282.4f3b   7.4   5.4(2)       Unknown      Other  <======= is this suppose to show "OK"?

Mod Sub-Module                  Model           Serial           Hw     Status

--- --------------------------- --------------- --------------- ------- -------

  1 Policy Feature Card         WS-F6K-PFC      SAD050206MX      1.1    Other  <======= is this suppose to show "OK"?

  1 Cat6k MSFC 2 daughterboard  WS-F6K-MSFC2    SAD04420LNZ      1.7    Ok    

There's an error message:

00:07:36: SP: slot1: lcp failed to go online

6 REPLIES
Hall of Fame Super Gold

Cisco 6506 unable to detect modules

Re: Cisco 6506 unable to detect modules

No, I'm not able to bootup my supervisor with CatOS, so I'm using the one with IOS.

But I did try this:

Router#hw-module module 3 reset

% unable to reset module 3: no card present

Not sure if it is the same.

Hall of Fame Super Gold

Cisco 6506 unable to detect modules

If it's IOS then the command is:

conf t

power enable  module

end

Re: Cisco 6506 unable to detect modules

Router(config)#power enable module 3

% nonexistent FRU

Re: Cisco 6506 unable to detect modules

Brought the modules to a reseller.
Put it in their chassis... and it runs...

Router#sh ver

Cisco Internetwork Operating System Software

IOS (tm) c6sup2_rp Software (c6sup2_rp-JSV-M), Version 12.1(8b)E15, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

TAC Support: http://www.cisco.com/tac

Copyright (c) 1986-2003 by cisco Systems, Inc.

Compiled Thu 17-Jul-03 19:52 by hqluong

Image text-base: 0x40008980, data-base: 0x4170A000

ROM: System Bootstrap, Version 12.1(11r)E1, RELEASE SOFTWARE (fc1)

BOOTFLASH: c6sup2_rp Software (c6sup2_rp-JSV-M), Version 12.1(8b)E15, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

Router uptime is 2 minutes

System returned to ROM by power-on (SP by power-on)

System image file is "bootflash:c6sup12-jsv-mz.121-8b.e15"

cisco Catalyst 6000 (R7000) processor with 227328K/34816K bytes of memory.

Processor board ID SAD04420LNZ

R7000 CPU at 300Mhz, Implementation 39, Rev 2.1, 256KB L2, 1024KB L3 Cache

Last reset from power-on

Bridging software.

X.25 software, Version 3.0.0.

SuperLAT software (copyright 1990 by Meridian Technology Corp).

TN3270 Emulation software.

1 Virtual Ethernet/IEEE 802.3  interface(s)

96 FastEthernet/IEEE 802.3 interface(s)

2 Gigabit Ethernet/IEEE 802.3 interface(s)

381K bytes of non-volatile configuration memory.

32768K bytes of Flash internal SIMM (Sector size 512K).

Configuration register is 0x2102

Router#sh mod

Mod Ports Card Type                              Model              Serial No.

--- ----- -------------------------------------- ------------------ -----------

  1    2  Cat 6000 sup 1 Enhanced QoS (Active)   WS-X6K-SUP1A-2GE   SAD05010NXB

  3   48  48 port 10/100 mb RJ45                 WS-X6348-RJ-45     SAD04250LF3

  5   48  48 port 10/100 mb RJ45                 WS-X6348-RJ-45     SAD041809EF

Mod MAC addresses                       Hw    Fw           Sw           Status

--- ---------------------------------- ------ ------------ ------------ -------

  1  0003.3282.4f3a to 0003.3282.4f3b   7.4   5.4(2)       6.2(2.113)   Ok

  3  00b0.c2f6.65bc to 00b0.c2f6.65eb   1.1   5.3(1)       6.2(2.113)   Ok

  5  0001.970e.27f0 to 0001.970e.281f   1.1   5.3(1)       6.2(2.113)   Ok

Mod Sub-Module                  Model           Serial           Hw     Status

--- --------------------------- --------------- --------------- ------- -------

  1 Policy Feature Card         WS-F6K-PFC      SAD050206MX      1.1    Ok

  1 Cat6k MSFC 2 daughterboard  WS-F6K-MSFC2    SAD04420LNZ      1.7    Ok

Router#dir slot0:

Directory of slot0:/

    1  -rw-       28945   Jul 10 2004 08:49:01  sinb02-confg

    2  -rw-    14600708   Jun 18 2000 03:17:24  c6sup12-jsv-mz.121-8b.e15

    3  -rw-     1703448   Jun 18 2000 03:32:55  c6msfc2-boot-mz.121-8b.E15.bin

    4  -rw-       27708   Jul 12 2004 11:03:13  sinb02-config-Jul12

24772608 bytes total (8411284 bytes free)

Router#dir bootflash:

Directory of bootflash:/

    1  -rw-     1703448   Nov 28 2011 17:17:44  c6msfc2-boot-mz.121-8b.E15

31981568 bytes total (30277992 bytes free)

Router#dir sup

Router#dir sup-b

Router#dir sup-bootflash:

Directory of sup-bootflash:/

    1  -rw-    14600708   Jun 04 2004 01:09:17  c6sup12-jsv-mz.121-8b.e15

    2  -rw-        4067   Jun 04 2004 01:14:39  switch.cfg

15990784 bytes total (1385752 bytes free)

Router#

Router#sh mod 3

Mod Ports Card Type                              Model              Serial No.

--- ----- -------------------------------------- ------------------ -----------

  3   48  48 port 10/100 mb RJ45                 WS-X6348-RJ-45     SAD04250LF3

Mod MAC addresses                       Hw    Fw           Sw           Status

--- ---------------------------------- ------ ------------ ------------ -------

  3  00b0.c2f6.65bc to 00b0.c2f6.65eb   1.1   5.3(1)       6.2(2.113)   Ok

Router#sh mod 5

Mod Ports Card Type                              Model              Serial No.

--- ----- -------------------------------------- ------------------ -----------

  5   48  48 port 10/100 mb RJ45                 WS-X6348-RJ-45     SAD041809EF

Mod MAC addresses                       Hw    Fw           Sw           Status

--- ---------------------------------- ------ ------------ ------------ -------

  5  0001.970e.27f0 to 0001.970e.281f   1.1   5.3(1)       6.2(2.113)   Ok

So the problem is either "me", or the chassis backplane.
Gonna bring the Chassis down for a check, just to be sure.

Guess, I'll have to prepare for the worst.

Cisco 6506 unable to detect modules

Resolved.

Changed Chassis.

946
Views
0
Helpful
6
Replies
CreatePlease to create content