Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Cisco 6509 Switch IOS Problem

HI

i have 1 6509 with these modules

ws-x6k-sup1a-2ge 2 modules x

ws-x6248-rj-45 2 mobules

ws-x6348 3 modules

ws-x6624-fxs 1 module

the problem i have is there is no IOS/ Catos installed in the Boot flash or slot0. can any one suggest me for the sutable ios and CatOS , please its very very urgent

2 REPLIES
Purple

Re: Cisco 6509 Switch IOS Problem

You don't mention how much DRAM the SUP1 card which is necessary to determine what code you can run . Some early modules only had 64 meg of dram only had 64 meg installed while later ones had 128 meg. If it only has 64 meg I would go with cat6000-supk8.7-4-3.bin . If it has 128 you can use anything you want with the caveat being you read the release notes for any rommon requirements . It want GD code use the latest 7.6 code which I think is like 7.6.17 at this point.

New Member

Re: Cisco 6509 Switch IOS Problem

sup1 DRAM is 128 flash card is 20 mb . i installed cat6000-supk8.7-4-3.bin through Xmodem. after that i am getting errors. they are

System Power On Diagnostics Complete

Boot image: mkseg1:a000e040

In Local Test Mode, Synch Failed. Retries: 4

WARNING: Pinnacle has not synchronised

Local Test Mode encounters Minor hardware problem in Module # 1

Runtime image not stored in the flash. Flash sync disabled.

Running System Diagnostics from this Supervisor (Module 1)

This may take up to 2 minutes....please wait

Pinnacle Synch Failed. Retries: 4

WARNING: Pinnacle has not synchronised

Minor hardware problem in Module # 1

Use 'show test 1' to see results of tests.

Cisco Systems Console

%SYS-1-SYS_ENABLEPS: Power supply 1 enabled

Enter password: %SYS-5-MOD_PWRON:Module 3 powered up

%SYS-5-MOD_PWRON:Module 4 powered up

%SYS-5-MOD_PWRON:Module 5 powered up

%SYS-5-MOD_PWRON:Module 6 powered up

%SYS-5-MOD_PWRON:Module 7 powered up

%SYS-5-MOD_PWRON:Module 9 powered up

%SYS-3-MOD_MINORFAIL:Minor problem in module 1

%MLS-5-FLOWMASKCHANGE:IP flowmask changed from DEST to FULL

%MLS-5-NDEDISABLED:Netflow Data Export disabled

%MLS-5-MCAST_STATUS:IP Multicast Multilayer Switching is enabled

Pinnacle Synch Failed. Retries: 4

WARNING: Switching bus not synchronised

%SYS-5-MOD_OK:Module 1 is online

%SYS-5-MOD_REMOVE:Module 4 has been removed

%SYS-5-MOD_PWRON:Module 4 powered up

%SYS-5-MOD_INSERT:Module 4 has been inserted

WARNING: Module 3 Pinnacle has not synchronised

%SYS-3-MOD_FAIL:Module 4 failed to come online

%SYS-5-MOD_REMOVE:Module 4 has been removed

after this how can i copy this file in to the bootflash/Flash . when i applied the command which boot its showing

Console> (enable) whichboot

Boot image name is 'mkseg1:a000e040'.

Console> (enable)

354
Views
0
Helpful
2
Replies