Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

CISCO-POP-MGMP-MIB doesn't works

Hi,

i have one Cisco3620 router with one 8 ISDN Basic Rate interface, and version 12.2(6) IOS. The router is properly configured for ISDN dial-in users, and i want to monitor the active calls with MRTG, or RRDTools via SNMP queries.

I red about interested CISCO-POP-MGMP-MIB entries from Cisco's Dial NMS implementation guide, and when try to use these, the answer is:

$snmpwalk 10.1.0.1 drvread .1.3.6.1.4.1.9.10.19

enterprises.9.10.19.1.1.2.0 = Gauge32: 0

enterprises.9.10.19.1.1.3.0 = Gauge32: 0

enterprises.9.10.19.1.1.4.0 = Gauge32: 0

enterprises.9.10.19.1.1.5.0 = Gauge32: 0

enterprises.9.10.19.1.1.6.0 = Gauge32: 0

enterprises.9.10.19.1.1.7.0 = Gauge32: 0

enterprises.9.10.19.1.1.8.0 = Counter32: 0

enterprises.9.10.19.1.1.10.0 = Gauge32: 0

enterprises.9.10.19.1.1.11.0 = Gauge32: 0

enterprises.9.10.19.1.1.12.0 = Gauge32: 0

enterprises.9.10.19.1.2.1.0 = Counter32: 0

enterprises.9.10.19.1.2.2.0 = Counter32: 0

enterprises.9.10.19.1.2.3.0 = Counter32: 0

enterprises.9.10.19.1.2.4.0 = Counter32: 0

enterprises.9.10.19.1.2.5.0 = Counter32: 0

enterprises.9.10.19.1.2.6.0 = Counter32: 0

enterprises.9.10.19.1.4.1.0 = 100

enterprises.9.10.19.1.4.2.0 = 15

enterprises.9.10.19.1.5.1.0 = 2

enterprises.9.10.19.1.6.1.0 = 2

Can I somehow monitor the active call's with SNMP from 3620, or this works only with 5xxx ASs? Why doesn't work the mentioned MIB?

Best regards,

Qrta

----------o<------------

and the answare was:

----------o<------------

mljohnson - CISCO SYSTEMS, CCIE

Oct 24, 2002, 11:22am PST

Yes, this should be supported by the 3620:

http://www.cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtml

MRTG should not be a problem, either:

http://www.cisco.com/univercd/cc/td/doc/cisintwk/intsolns/dialsol/nmssol/mrtg.htm

You may want to try the Network Management group for more help.

----------o<------------

So, works the MIB, or not?

Best regards,

Qrta

4 REPLIES
Blue

Re: CISCO-POP-MGMP-MIB doesn't works

Do you have the IOS image name available running on this 3620 as seen in the 'sh ver' output?

New Member

Re: CISCO-POP-MGMP-MIB doesn't works

Hi,

the show ver is:

Cisco Internetwork Operating System Software

IOS (tm) 3600 Software (C3620-I-M), Version 12.2(6), RELEASE SOFTWARE (fc2)

Copyright (c) 1986-2001 by cisco Systems, Inc.

Compiled Wed 07-Nov-01 19:41 by pwade

Image text-base: 0x600089A8, data-base: 0x60A60000

ROM: System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

drvisdn uptime is 15 weeks, 2 hours, 1 minute

System returned to ROM by power-on

System image file is "flash:c3620-i-mz.122-6.bin"

cisco 3620 (R4700) processor (revision 0x81) with 24576K/8192K bytes of memory.

Processor board ID 18045113

R4700 CPU at 80Mhz, Implementation 33, Rev 1.0

Bridging software.

X.25 software, Version 3.0.0.

Basic Rate ISDN software, Version 1.1.

1 Ethernet/IEEE 802.3 interface(s)

1 Serial network interface(s)

8 ISDN Basic Rate interface(s)

DRAM configuration is 32 bits wide with parity disabled.

29K bytes of non-volatile configuration memory.

8192K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

Standard IP featureset.

Best regards, Qrta

Blue

Re: CISCO-POP-MGMP-MIB doesn't works

CCO MIB Locatore Tool does show that c3620-i-mz.122-6.bin have this MIB present. Have you searched CCO Bug Toolkit to see if there are any open defects related to this?

New Member

Re: CISCO-POP-MGMP-MIB doesn't works

As I see only 12.2T supports this MIB? Sorry, I haven't saw that yet... I'll try it.

Thanx,

Qrta

117
Views
0
Helpful
4
Replies
CreatePlease to create content