Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Configure 876W - How to configure? - No progress up to now!!!

Hi,

After many tries and advices i still can not configure my router properly...

So i am uploading the topology, a file with the wired (and operational - Config_1_BVI1.txt) configuration, and a file with the last try...

On this topology the wired part works fine...

Now i want to set up the wireless part. I do not know if is this possible... I have followed many suggestions but still nothing...

So does anybody knows how to configure my wireless lan...

i would, really preciate it, if someone could send me a configuration file... or a set of cli commands...

3 REPLIES
VIP Purple

Re: Configure 876W - How to configure? - No progress up to now!!

Hello,

I remember your previous post. I have tried to put the configuration together (see below). Basically, you need to connect your access point to interface FastEthernet 4.

If this still doesn't work, let me know:

bridge irb

!

!

interface BRI0

no ip address

no ip redirects

no ip unreachables

no ip proxy-arp

ip route-cache flow

shutdown

no cdp enable

!

interface ATM0

no ip address

no ip redirects

no ip unreachables

no ip proxy-arp

ip route-cache flow

shutdown

no atm ilmi-keepalive

dsl operating-mode auto

!

interface FastEthernet0

no ip address

no cdp enable

!

interface FastEthernet1

no ip address

no cdp enable

!

interface FastEthernet2

no ip address

no cdp enable

!

interface FastEthernet3

no ip address

no cdp enable

!

interface FastEthernet4

ip address 192.168.0.X

no ip directed-broadcast (default)

speed auto

ip nat outside

no cdp enable

!

interface Dot11Radio0

no ip address

!

ssid OFFICENET

vlan 1

authentication open

!

ssid ciscowep

vlan 2

authentication open

!

speed basic-1.0 2.0 5.5 6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0

channel 2437

station-role root

no cdp enable

!

interface Dot11Radio0.1

encapsulation dot1Q 1 native

no cdp enable

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 spanning-disabled

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

!

interface Dot11Radio0.2

encapsulation dot1Q 2

bridge-group 2

bridge-group 2 subscriber-loop-control

bridge-group 2 spanning-disabled

bridge-group 2 block-unknown-source

no bridge-group 2 source-learning

no bridge-group 2 unicast-flooding

interface Vlan1

description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$$FW_INSIDE$

ip address X.X.X.X 255.255.255.0

ip nat inside

bridge-group 1

bridge-group 1 spanning-disabled

!

interface Vlan2

no ip address

bridge-group 2

bridge-group 2 spanning-disabled

!

interface BVI1

ip address 192.168.100.1 255.255.255.0

!

interface BVI2

ip address 192.168.2.1 255.255.255.0

ip classless

!

ip http server

ip http authentication local

ip http secure-server

ip http timeout-policy idle 5 life 86400 requests 10000

!

logging trap debugging

no cdp run

route-map ON_Route permit 10

match ip address 1

!

!

control-plane

!

bridge 1 route ip

bridge 2 route ip

!

banner login ^CAuthorized access only!

Disconnect IMMEDIATELY if you are not an authorized user!^C

!

line con 0

login local

no modem enable

transport preferred all

transport output telnet

line aux 0

login local

transport preferred all

transport output telnet

line vty 0 4

privilege level 15

login local

transport preferred all

transport input telnet ssh

transport output all

!

scheduler max-task-time 5000

scheduler allocate 4000 1000

scheduler interval 500

end

Regards,

GP

New Member

Re: Configure 876W - How to configure? - No progress up to now!!

Hi Georg

Thank you for your reply... as i told you i had no luck so far and i really need someone to help me...

You say to me, to try to connect my AP on port FastEthernet 4. You mean FastEthenet 3 (FE3) on the router? I am asking you because my router has 4 FastEthernet ports from FE0 - FE3, one ISDN and one ADSLoISDN...

Please forgive me, if i do not understand something, but its the first time on routers, and the first Cisco Router i ever had...

Many regards

Antonis

VIP Purple

Re: Configure 876W - How to configure? - No progress up to now!!

Hello Antonis,

my apologies, I thought you were using PPPoE, while you are using ATM. Try this configuration (I added and changed a few things). The username and password configured under the dialer interface should have been given to you by your provider.

If this doesn´t work, try and contact me offline, my Skype, my ID is ´solutionfindershelpdesk´, otherwise my email address is pauwen@hotmail.com.

bridge irb

!

!

interface BRI0

no ip address

no ip redirects

no ip unreachables

no ip proxy-arp

ip route-cache flow

shutdown

no cdp enable

!

interface ATM0

no ip address

no ip redirects

no ip unreachables

no ip proxy-arp

ip route-cache flow

no atm ilmi-keepalive

dsl operating-mode auto

!

interface ATM0.1 point-to-point

pvc 0/100

encapsulation aal5mux ppp dialer

dialer pool-member 1

!

interface FastEthernet0

no ip address

no cdp enable

!

interface FastEthernet1

no ip address

no cdp enable

!

interface FastEthernet2

no ip address

no cdp enable

!

interface FastEthernet3

no ip address

no cdp enable

!

interface Dot11Radio0

no ip address

!

ssid OFFICENET

vlan 1

authentication open

!

ssid ciscowep

vlan 2

authentication open

!

speed basic-1.0 2.0 5.5 6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0

channel 2437

station-role root

no cdp enable

!

interface Dot11Radio0.1

encapsulation dot1Q 1 native

no cdp enable

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 spanning-disabled

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

!

interface Dot11Radio0.2

encapsulation dot1Q 2

bridge-group 2

bridge-group 2 subscriber-loop-control

bridge-group 2 spanning-disabled

bridge-group 2 block-unknown-source

no bridge-group 2 source-learning

no bridge-group 2 unicast-flooding

interface Vlan1

description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$$FW_INSIDE$

ip address X.X.X.X 255.255.255.0

ip nat inside

bridge-group 1

bridge-group 1 spanning-disabled

!

interface Vlan2

no ip address

bridge-group 2

bridge-group 2 spanning-disabled

!

interface BVI1

ip address 192.168.100.1 255.255.255.0

!

interface BVI2

ip address 192.168.2.1 255.255.255.0

ip classless

!

interface Dialer0

ip ddns update sdm_ddns1

ip address negotiated

ip nat outside

ip virtual-reassembly

encapsulation ppp

dialer pool 1

dialer-group 1

no cdp enable

ppp authentication chap pap callin

ppp chap hostname USERID

ppp chap password 7 PASSWORD

ppp pap sent-username USERID password

!

ip http server

ip http authentication local

ip http secure-server

ip http timeout-policy idle 5 life 86400 requests 10000

!

logging trap debugging

no cdp run

route-map ON_Route permit 10

match ip address 1

!

ip nat inside source list 1 interface Dialer0 overload

!

access-list 1 permit 192.168.100.0

access-list 1 permit 192.168.2.0

!

control-plane

!

ip route 0.0.0.0 0.0.0.0 Dialer0

!

bridge 1 route ip

bridge 2 route ip

!

banner login ^CAuthorized access only!

Disconnect IMMEDIATELY if you are not an authorized user!^C

!

line con 0

login local

no modem enable

transport preferred all

transport output telnet

line aux 0

login local

transport preferred all

transport output telnet

line vty 0 4

privilege level 15

login local

transport preferred all

transport input telnet ssh

transport output all

!

scheduler max-task-time 5000

scheduler allocate 4000 1000

scheduler interval 500

end

118
Views
5
Helpful
3
Replies