03-08-2006 02:08 AM - edited 03-03-2019 02:10 AM
Hi,
I have two 7200's connected to a 2950 (FE 22 + FE 24 - Both configured as trunks).
On the 7200's, I have the following:
7200-A
!
interface FastEthernet0/0.23
encapsulation dot1Q 23
ip address 192.168.1.1 255.255.255.252
no snmp trap link-status
!
7200-B
!
interface FastEthernet0/0.23
encapsulation dot1Q 23
ip address 192.168.1.2 255.255.255.252
no snmp trap link-status
!
2950:
!
interface FastEthernet0/22
switchport mode trunk
no ip address
duplex full
speed 100
!
interface FastEthernet0/24
switchport mode trunk
no ip address
duplex full
speed 100
!
But I cannot ping between the two routers?
03-08-2006 02:17 AM
Hi Friend,
Can you cofirm if you have vlan 23 in your vlan database.
Can you check with "sh vlan" if vlan 23 is not present please create in going to vlan database mode.
Regards,
Ankur
03-08-2006 02:17 AM
Hi,
Can you enter in 'switchport trunk encapsulation dot1q' under both interfaces Fa0/22 and Fa0/24 on your switch ? I'm pretty sure the 2950 defaults to ISL encapsulation on trunks.
Hope that helps - pls rate the post if it does.
Paresh
03-08-2006 02:21 AM
Hi Paresh,
2950 only supports dot1q so I do not think this command will even work with 2950.
Regards,
Ankur
03-08-2006 02:25 AM
Thanks Ankur,
I was confusing it with the 2900XL switches :-(
Paresh
03-08-2006 02:19 AM
What are you trying to accomplish?
You don't need to configure a trunk on the router unless you want to route VLANs on the 2950 switch i.e.""router-on-a-stick" concept.
You can make both ports on the 2950 access ports by configuring the following:
int Fa0/22 , Fa0/24
switchport
switchport mode access
switchport access vlan 23
duplex full
speed 100
This makes both ports member of VLAN 23. You can now ping router 7200-B from 7200-A and vice versa.
HTH
Leon
* Please rate useful posts
03-08-2006 02:22 AM
You can chech the status of the trunk with the following commands:
* show trunks
* show interface Fa0/22 switchport
* show interface Fa0/24 trunk
This should give you an impression what is allowed on the trunk and if VLAN 23 traverses the trunk.
Leon
03-08-2006 03:23 AM
7200-A has dot1q ints for servers connected to the 2950 (Access Ports)....these are all currently successfully trunked down FE24
I want to connect 7200-B to 7200-A, and have dot1q Ints on both routers(As /30's) that can communicate (They will be used on 7200-B as Internet gateways for VRF's (With IP Nat enabled)....I was hoping that by having 7200-B connected to 2950 FE22, and configuring that port as a trunk also, that the dot1q ints on both routers could talk.
vlan 23 does exist on 2950, and is being trunked on both FE 22 + FE 24
I dont have any spare FE ports on 7200-A, hence the reason for me connecting 7200-B to the 2950.
03-08-2006 03:32 AM
Hi Friend,
Can you check the arp entries in your router. I mean from router A can you check "sh ip arp
Is it possible to paste the complete sh run from both the routers, looks like something fishy happening.
Ankur
03-09-2006 04:19 PM
Howdy-
Try setting your native vlan to 23 on each of the interfaces on the 2950.
Traffic in the native VLAN is untagged and the default native VLAN is 1.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: