Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

DS3 alarm on PA-A3-T3

Hello,

I noticed the following output when I perform debug ATM event /error, this happen to both of my router Cisco 7204VXR using PA-A3-T3, I try to install the fixed attenuator, and it does not solve the problem.

The hardware revision of the PA-A3-T3 is 4.0, IOS version 12.2(4)BW1

Jan 18 15:32:15.058 GMT: pmc_pm7345_isr: received framer int 0x08, old alarm 0x0000

Jan 18 15:32:15.058 GMT: ds3 alarm indication 0x10 status 0x30 alarm 0x0010

Jan 18 15:32:15.058 GMT: atmdx_alarm_handler(ATM1/0): alarm 0x0010, state 4

Jan 18 15:32:15.058 GMT: ATM1/0: LED turned 1

Jan 18 15:32:15.062 GMT: pmc_pm7345_isr: received framer int 0x08, old alarm 0x0010

Jan 18 15:32:15.062 GMT: ds3 alarm indication 0x10 status 0x20 alarm 0x0000

Jan 18 15:32:15.062 GMT: atmdx_alarm_handler(ATM1/0): alarm 0x0000, state 0

Jan 18 15:32:15.062 GMT: ATM1/0: LED turned 0

Jan 18 15:32:15.062 GMT: pmc_pm7345_isr: received framer int 0x40, old alarm 0x0000

Jan 18 15:32:15.118 GMT: pmc_pm7345_isr: received framer int 0x08, old alarm 0x0000

Jan 18 15:32:15.118 GMT: ds3 alarm indication 0x22 status 0x02 alarm 0x0002

Jan 18 15:32:15.118 GMT: atmdx_alarm_handler(ATM1/0): alarm 0x0002, state 4

Jan 18 15:32:15.118 GMT: ATM1/0: LED turned 1

Jan 18 15:32:15.118 GMT: pmon_change 0x01, cppm_change 0x70

Jan 18 15:32:15.126 GMT: pmc_pm7345_isr: received framer int 0x08, old alarm 0x0002

Jan 18 15:32:15.126 GMT: ds3 alarm indication 0xA2 status 0x20 alarm 0x0000

Jan 18 15:32:15.126 GMT: atmdx_alarm_handler(ATM1/0): alarm 0x0000, state 0

Jan 18 15:32:15.126 GMT: ATM1/0: LED turned 0

Jan 18 15:32:15.126 GMT: pmc_pm7345_isr: received framer int 0x60, old alarm 0x0000

Jan 18 15:32:15.310 GMT: pmon_change 0x16, cppm_change 0x78

Jan 18 15:34:38.133 GMT: pmc_pm7345_isr: received framer int 0x08, old alarm 0x0000

Jan 18 15:34:38.133 GMT: ds3 alarm indication 0x10 status 0x30 alarm 0x0010

Jan 18 15:34:38.133 GMT: atmdx_alarm_handler(ATM1/0): alarm 0x0010, state 4

Jan 18 15:34:38.133 GMT: ATM1/0: LED turned 1

Jan 18 15:34:38.141 GMT: pmc_pm7345_isr: received framer int 0x08, old alarm 0x0010

Jan 18 15:34:38.141 GMT: ds3 alarm indication 0x10 status 0x20 alarm 0x0000

Jan 18 15:34:38.141 GMT: atmdx_alarm_handler(ATM1/0): alarm 0x0000, state 0

Jan 18 15:34:38.141 GMT: ATM1/0: LED turned 0

Jan 18 15:34:38.141 GMT: pmc_pm7345_isr: received framer int 0x40, old alarm 0x0000

Jan 18 15:34:38.273 GMT: pmc_pm7345_isr: received framer int 0x08, old alarm 0x0000

Jan 18 15:34:38.273 GMT: ds3 alarm indication 0x92 status 0x30 alarm 0x0010

Jan 18 15:34:38.273 GMT: atmdx_alarm_handler(ATM1/0): alarm 0x0010, state 4

Jan 18 15:34:38.273 GMT: ATM1/0: LED turned 1

Jan 18 15:34:38.273 GMT: pmon_change 0x01, cppm_change 0x70

Jan 18 15:34:38.277 GMT: pmc_pm7345_isr: received framer int 0x08, old alarm 0x0010

Jan 18 15:34:38.277 GMT: ds3 alarm indication 0x10 status 0x20 alarm 0x0000

Jan 18 15:34:38.277 GMT: atmdx_alarm_handler(ATM1/0): alarm 0x0000, state 0

Jan 18 15:34:38.277 GMT: ATM1/0: LED turned 0

Jan 18 15:34:38.277 GMT: pmc_pm7345_isr: received framer int 0x40, old alarm 0x0000

Jan 18 15:34:38.309 GMT: pmon_change 0x01, cppm_change 0x78

Thanks for any recommendation /advise.

Regards

Shinyaw

1 REPLY
Bronze
160
Views
0
Helpful
1
Replies