Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements
Webcast-Catalyst9k
New Member

Equivalent Command for "sh top"

Hi ,

whats the equivalent of "sh top'(which runs in CatOS) command in IOS , is it Sh interface x/y ??

regards

Neo

1 ACCEPTED SOLUTION

Accepted Solutions

Re: Equivalent Command for "sh top"

Hello Neo,

you could try "show interface summary" its not 100% the same, but its helpful.

HTH,

if it does, please rate this post.

vlad

switch-ud-2a>show interfaces summary

*: interface is up

IHQ: pkts in input hold queue IQD: pkts dropped from input queue

OHQ: pkts in output hold queue OQD: pkts dropped from output queue

RXBS: rx rate (bits/sec) RXPS: rx rate (pkts/sec)

TXBS: tx rate (bits/sec) TXPS: tx rate (pkts/sec)

TRTL: throttle count

Interface IHQ IQD OHQ OQD RXBS RXPS TXBS TXPS TRTL

---------------------------------------------------------------------

Vlan1 0 0 0 0 0 0 0 0 0

Vlan99 0 0 0 0 0 0 0 0 0

* Vlan164 0 0 0 0 0 0 0 0 0

* Vlan165 0 0 0 0 0 0 0 0 0

* Vlan166 0 0 0 0 0 0 261000 167 0

Vlan167 0 0 0 0 0 0 0 0 0

* Vlan168 0 0 0 0 0 0 0 0 0

* Vlan169 0 0 0 0 0 0 0 0 0

* Vlan170 0 0 0 0 0 0 0 0 0

* Vlan171 0 0 0 0 452000 313 119000 101 0

* Vlan172 0 0 0 0 0 0 0 0 0

4 REPLIES

Re: Equivalent Command for "sh top"

Hello Neo,

you could try "show interface summary" its not 100% the same, but its helpful.

HTH,

if it does, please rate this post.

vlad

switch-ud-2a>show interfaces summary

*: interface is up

IHQ: pkts in input hold queue IQD: pkts dropped from input queue

OHQ: pkts in output hold queue OQD: pkts dropped from output queue

RXBS: rx rate (bits/sec) RXPS: rx rate (pkts/sec)

TXBS: tx rate (bits/sec) TXPS: tx rate (pkts/sec)

TRTL: throttle count

Interface IHQ IQD OHQ OQD RXBS RXPS TXBS TXPS TRTL

---------------------------------------------------------------------

Vlan1 0 0 0 0 0 0 0 0 0

Vlan99 0 0 0 0 0 0 0 0 0

* Vlan164 0 0 0 0 0 0 0 0 0

* Vlan165 0 0 0 0 0 0 0 0 0

* Vlan166 0 0 0 0 0 0 261000 167 0

Vlan167 0 0 0 0 0 0 0 0 0

* Vlan168 0 0 0 0 0 0 0 0 0

* Vlan169 0 0 0 0 0 0 0 0 0

* Vlan170 0 0 0 0 0 0 0 0 0

* Vlan171 0 0 0 0 452000 313 119000 101 0

* Vlan172 0 0 0 0 0 0 0 0 0

Re: Equivalent Command for "sh top"

thanks Vlad i also get some information fromm this

will you give me some information regarding to catos and IOS???

hereby i rate your post and congratulation to get silverstar.

regards

Devang

Re: Equivalent Command for "sh top"

Thanks Devang,

what kind of information are you looking for on CATOS x IOS?

There are some good cisco texts that compare these 2 OS.

Difference Between CatOS and Cisco IOS System Software

http://www.cisco.com/en/US/products/hw/switches/ps708/products_tech_note09186a008015bfa6.shtml#diff

Vlad

Purple

Re: Equivalent Command for "sh top"

As far as I know there is no real equivalent for the show top which is a basically timed report of whats happened for say the last 15 minutes . For traffic counters you can use "show interface counters" , for error type traffic you can use "show interface counters errors" .

148
Views
4
Helpful
4
Replies
CreatePlease to create content